Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot Rifter 2020-2023 Owner's Manual Lighting and visibility Wiper control stalk

88Lighting and visibilityHeadlamp beam height adjustmentTo avoid inconvenience to other road users, the height of the halogen headlamps should be adjusted according to the load in the vehicle.0(Initial setting)Unladen.1Partial load.2Medium load.3Maximumauthorisedload.4 5 6Not used.Wiper control stalkBefore operating the wipers in wintry conditions, clear any snow, ice or frost from the windscreen and around the wiper arms and blades.Do not operate the wipers on a dry windscreen. In extremely hot or cold weather, check that the wiper blades are not stuck to the windscreen before operating the wipers.After using an automatic car wash, you may temporarily notice abnormal noises and poorer wiping performance. You do not need to replace the wiper blades.Without AUTO wipingWith AUTO wipingWindscreen wipers►To select the wiping speed: raise or lower the stalk to the desired position.Fast wiping (heavy rain) Normal wiping (moderate rain) Intermittent wiping (proportional to the vehicle’s speed)Switching offSingle wipe (press down and release). orAutomatic wiping Refer to the corresponding section.Windscreen wash►Pull the wiper control stalk towards you and hold.A final wiping cycle is performed when screenwashing ends.The windscreen wash jets are incorporated into the tip of each wiper arm.Screenwash fluid is sprayed along the length of the wiper blade. This improves visibility and reduces screenwash fluid consumption.With automatic air conditioning, any action on the screenwash control results in temporary closure of the air intake to protect the passenger compartment from any odour.
89Lighting and visibility4To avoid damaging the wiper blades, do not operate the screenwash if the screenwash reservoir is empty.Only operate the screenwash if there is no risk of the fluid freezing on the windscreen and hindering visibility. During the winter period, use "very cold climate" rated products.Never top up with water.Low screenwash fluid levelWhen the low level of the reservoir is reached, this warning lamp lights up on the instrument panel, accompanied by an audible signal and a message.It comes on when the ignition is switched on, or every time the stalk is operated, until the reservoir is refilled.Refill the screenwash reservoir (or have it refilled) the next time you stop.Rear wiper►Turn the ring to align the desired symbol with the marking.OffIntermittent wiping Screenwash-wipe Reverse gearWhen reverse gear is engaged, the rear wiper will come into operation automatically if the front windscreen wipers are operating.Activation/DeactivationThe settings are changed via the Driving/Vehicle touch screen menu.This function is activated by default. In the event of accumulation of snow or hard frost or if a bicycle carrier is fitted to a towing device, deactivate the automatic rear wiper via the touch screen’s Driving/Vehiclemenu.Special position of the windscreen wipersThis maintenance position is used while cleaning or replacing the wiper blades. It can also be useful, in wintry weather (ice, snow), to release the wiper blades from the windscreen.To maintain the effectiveness of the flat wiper blades, it is advisable to:–handle them with care.–clean them regularly using soapy water.–avoid using them to hold cardboard on the windscreen.–replace them at the first signs of wear.Before removing a windscreen wiper bladeOperating the wiper control stalk immediately after switching off the ignition will place the wiper blades in a vertical position.►Proceed with the desired operation or the replacement of the wiper blades.After refitting a windscreen wiper blade►To return the wiper blades to their initial position after the operation, switch on the ignition and operate the wiper control stalk.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131