Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot Rifter 2020-2023 Owner's Manual In the event of a breakdown Tool kit

200In the event of a breakdownRunning out of fuel (Diesel)With Diesel engines, the fuel system must be primed if you run out of fuel.Before starting to prime the system, it is essential to put at least 5 litres of Diesel into the fuel tank.For more information on Refuelling and on Misfuel prevention (Diesel), refer to the corresponding section.For non-BlueHDi versions, the fuel system components are located in the engine compartment; this may be under a removable cover.For more information on the Engine compartment, in particular the location of these components under the bonnet, refer to the corresponding section.With 1.6 BlueHDi (Euro 6.1)►Switch on the ignition (without starting the engine).►Wait around 6seconds and switch off the ignition.►Repeat the operation 10times.►Operate the starter motor to start the engine.If the engine does not start at the first attempt, do not keep trying, but restart the procedure.With 1.5 BlueHDi (Euro 6.2/6.3)►Switch on the ignition (without starting the engine).►Wait around 1minute and switch off the ignition.►Operate the starter motor to start the engine.If the engine does not start at the first attempt, do not keep trying, but restart the procedure.Non-BlueHDi engines►Open the bonnet and then, if necessary, unclip the cover to access the priming pump.►Operate the priming pump repeatedly until resistance is felt (resistance may be felt at the first press).►Operate the starter motor to start the engine (if the engine does not start at the first attempt, wait around 15 seconds before trying again).►If the engine does not start after a few attempts, operate the priming pump again, then the starter motor.►Put the cover back in place and clip it in, then close the bonnet.Tool kit►For easier access, move the seat(s) forward.Accessing the toolsVehicle with electric motorWith temporary puncture repair kitThe tools are located in the passenger footwell.With spare wheelThe tools are located under the right-hand front seat.To access the tools:–With non-adjustable front seat, lift the seat cushion by placing your hand between the cushion and the backrest.–With adjustable front seat, move the seat forward as far as possible.The jack is located in the passenger footwell.Vehicle with Petrol or Diesel engineWith temporary puncture repair kitThe kit is located under the right-hand front seat.With spare wheelThe jack is located under the right-hand front seat.The tools are located under the left-hand front seat.List of tools1.Chock to immobilise the vehicle2.Removable towing eye
201In the event of a breakdown83.Torx keyAllows the removal of the rear lamps in order to change a bulb.With temporary puncture repair kit4.12V compressor with cartridge of sealant and speed limit stickerFor temporary repair of a tyre and to adjust the tyre pressure.Storing the tools (vehicle with electric motor)Store the 12V compressor and sealant cartridge 4 inside the pouch as shown.The space inside the passenger footwell is narrow. In order to be able to close the hatch, store the tools in their initial locations: chock 1 outside the bag, removable eye2 on top of the bag with the buckle facing outwards, Torx key 3 on top of the bag, 12V compressor with sealant cartridge 4 inside the bag.For more information about the Temporary puncture repair kit, refer to the corresponding section.With spare wheel5.Wheelbrace.For removing the wheel bolts and raising/lowering the jack.6.Jack.Used to raise the vehicle.7.Wheel bolt cover/wheel trim removal tool (depending on equipment).If present on the vehicle, used to remove the wheel bolt covers on alloy wheels or the wheel trim on steel wheels.8.Socket for "anti-theft" wheel bolts.Used to adapt the wheelbrace to the special "anti-theft" bolts.For more information on the Spare wheel, please refer to the corresponding section.
202In the event of a breakdownAll of these tools are specific to your vehicle and may vary depending on equipment.Do not use them for any other purposes.The jack must only be used to change a wheel with a damaged or punctured tyre.The jack does not require any maintenance.The jack meets European standards, as defined in the Machinery Directive 2006/42/EC.Some parts of the jack such as the screws and hinges could cause injury: avoid touching them.Carefully remove any traces of grease.Temporary puncture repair kitScan the QR Code on page 3 to view explanatory videos.Made up of a compressor and a sealant cartridge,it allows you to carry out a temporary repair of the tyre so that you can drive to the nearest garage.It is designed to repair most punctures located on the tyre tread.The vehicle's electric system allows the connection of the compressor to the 12 V power supply for long enough to repair a tyre after a puncture.Only the 12 V socket located at the frontof the vehicle can be used to power the compressor.For more information on the Tool kit, refer to the corresponding section.Repair procedureDo not remove any foreign body (e.g.nail, screw) which has penetrated the tyre.►Park the vehicle without obstructing traffic and apply the parking brake.►Follow the safety instructions (hazard warning lamps, warning triangle, high visibility jacket, etc.) according to the legislation in force in the country in which you are driving.►Switch the ignition off.►Remove the valve cap from the tyre to be repaired, and place it in a clean place.►Connect the pipe from the bottle of sealant to the valve of the tyre to be repaired and tighten firmly.►Connect the pipe from the compressor to the bottle of sealant.►Check that the compressor switch is in position"O".►Fully uncoil the electric cable stowed under the compressor.►Connect the compressor's electric plug to the vehicle's 12V socket.►Affix the speed limit sticker.The speed limit sticker must be affixed inside the vehicle in the area close to the driver, to remind them that a wheel is in temporary use.►Switch the ignition on.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131