Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot Rifter 2020-2023 Owner's Manual Driving Reversing camera

161Driving6Deactivation/ActivationWithout touch screen►To deactivate or activate the system, press this button.The indicator lamp is on when the system is deactivated.With touch screenThe settings are changed via theDriving/Vehicletouch screen menu.The status of the function is saved when the ignition is switched off.The rear parking sensors system will be deactivated automatically if a trailer or bicycle carrier is connected to a towing device installed in accordance with the manufacturer's recommendations.In this case, the outline of a trailer is displayed at the rear of the image of the vehicle.The parking sensors are deactivated while the Park Assist function is measuring a space.For more information on the Park Assistfunction, refer to the corresponding section.Operating limitsIf the boot is heavily loaded, the vehicle may tilt, affecting distance measurements.MalfunctionIn the event of a malfunction when changing into reverse gear, this warning lamp lights up on the instrument panel, accompanied by the display of a message and an audible signal (short beep).Have it checked by a PEUGEOT dealer or a qualified workshop.Reversing cameraFor more information, refer to the General recommendations on the use of driving and manoeuvring aids.With the ignition on, this system uses a camera located near the third brake lamp to display a view of the rear of your vehicle on the reproduction screen (if it is a panel van or has a solid partition).The reversing camera is activated automatically when reverse gear is engaged. The image is displayed on the reproduction screen. The reproduction screen switches off when the gearbox is in neutral or in a forward gear.The blue lines 1 represent the general direction of the vehicle (the gap corresponds to the width of your vehicle with the mirrors).The red line 2 represents a distance of about 30cm beyond the edge of your vehicle's rear bumper.
162DrivingThe green lines 3 represent distances of about 1 and 2 metres beyond the edge of your vehicle's rear bumper.The turquoise blue curves 4 represent the maximum turning circle.Some objects may not be seen by the camera.Certain vehicles may be difficult to see (dark colours, lamps off) when the brightness of the screen is reduced using the vehicle’s lighting dimmer.The image quality may be affected by the surroundings, the exterior conditions (rain, dirt, dust), the driving mode and the lighting conditions (night, low sun).In the presence of areas in shade, or in conditions of bright sunlight or inadequate lighting, the image may be darkened and with lower contrast.Obstacles may appear further away than they actually are.During parking manoeuvres and lane changes, it is important to check the sides of the vehicle using the mirrors.The rear parking sensors also supplement the information on the vehicle's surroundings.Operating limitsThe system may be disrupted (or even damaged) and not work in the following situations:–Installation of a bicycle carrier on the tailgate or side-hinged door (depending on version).–Attachment of a trailer to the towball.–Driving with a door open.Please note, the camera must not be obscured (by a sticker, a bicycle carrier, etc.).The field of vision of the camera may vary depending on the load in vehicle.Maintenance recommendationsIn bad or wintry weather, ensure that the camera is not covered by mud, frost or snow.Check the cleanliness of the camera lens regularly.If necessary, clean the camera with a soft, dry cloth.When washing the vehicle using a high-pressure jet, keep the spray directed at least 30cm away from the camera.Surround Rear VisionFor more information, refer to the General recommendations on the use of driving and manoeuvring aids.With the ignition on, in order to improve visibility of the passenger side blind spot and the rear of the vehicle, this system uses two cameras to display the views of the vehicle’s close surroundings on the reproduction screen (panel van or fitted with a solid partition).This system has three sub-functions:
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131