Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot Rifter 2018-2019 Owner's Manual Driving Active Blind Spot Monitoring System

127Driving6–Your vehicle is not pulling a trailer, a caravan, etc.Operating limitsNo alert is triggered in the following conditions:–In the presence of non-moving objects (parked vehicles, barriers, street lamps, road signs, etc.).–Oncoming traffic.–Driving on a winding road or a sharp corner.–When overtaking or being overtaken by a very long vehicle (lorry, bus, etc.) that is detected in the rear blind spot but is also present in the driver’s front field of vision.–When overtaking quickly.–In very heavy traffic: vehicles detected in front and behind are confused with a lorry or a stationary object.MalfunctionIf the event of malfunction, this warning lamp comes on in the instrument panel, accompanied by the display of a message.Contact a PEUGEOT dealer or a qualified workshop to have the system checked.The system may suffer temporary interference in certain weather conditions (rain, hail, etc.).In particular, driving on a wet surface or moving from a dry area to a wet area can cause false alerts (for example, the presence of a fog of water droplets in the blind spot angle is interpreted as a vehicle).In bad or wintry weather, ensure that the sensors are not covered by mud, ice or snow.Take care not to cover the warning zone in the door mirrors or the detection zones on the front and rear bumpers with adhesive labels or other objects; they may hamper correct operation of the system.Active Blind Spot Monitoring SystemIn addition to the fixed warning lamp in the door mirror on the side in question, a correction of trajectory will be felt if you attempt to cross a lane marking with the direction indicators on, to help you avoid a collision.This system is the combination of the Active Lane Keeping Assistance and Blind Spot Monitoring System.These two functions must be activated and in operation.
128DrivingThe speed of the vehicle must be between 40 and 87 mph (65 and 140km/h) inclusive.These functions are especially suitable for driving on motorways and main roads.For more information on the Active Lane Keeping Assistance and Blind Spot Monitoring System, refer to the corresponding sections.This system is a driving aid which cannot, in any circumstances, replace the need for vigilance on the part of the driver.Distraction detectionRefer to the General recommendations on the use of driving and manoeuvring aids.Take a break in case of feeling tired or at least every 2 hours.Depending on version, the function comprises either the "Driver Attention Alert" system alone or combined with the "Driver Attention Alert by camera" system.These systems are in no way designed to keep the driver awake or to prevent the driver from falling asleep at the wheel. It is the driver’s responsibility to stop if feeling tired.Activation/DeactivationThe function is activated or deactivated via the vehicle configuration menu.The state of the system stays in the memory when the ignition is switched off.Driver Attention AlertThe system triggers an alert as soon as it detects that the driver has not taken a break after two hours of driving at a speed above 40 mph (65km/h).This alert is issued via the display of a message encouraging you to take a break, accompanied by an audible signal.If the driver does not follow this advice, the alert is repeated hourly until the vehicle is stopped.The system resets itself if one of the following conditions is met:–engine running, the vehicle has been stationary for more than 15 minutes,–the ignition has been switched off for a few minutes,–the driver's seat belt is unfastened and their door is opened.As soon as the speed of the vehicle drops below 40 mph (65km/h), the system goes into standby.The driving time is counted again once the speed is above 40 mph (65km/h).Driver Attention Alert by cameraDepending on version, the "Driver Attention Alert" may be combined with the "Driver Attention Alert by camera".Using a camera placed at the top of the windscreen, the system assesses the driver's level of vigilance, fatigue or distraction by identifying variations in trajectory compared to the lane markings.This system is particularly suited to fast roads (speed higher than 40 mph (65km/h)).At a first-level alert, the driver is warned by the “Take care!” message, accompanied by an audible signal.After three first-level alerts, the system triggers a further alert with the message "Dangerous driving: take a break", accompanied by a more pronounced audible signal.The following situations may interfere with the operation of the system or prevent it from working:–poor visibility (inadequate lighting of the road, falling snow, heavy rain, dense fog, etc.);–dazzle (headlamps of an oncoming vehicle, low sun, reflections on a damp road, leaving a tunnel, alternating shade and light, etc.);–windscreen area located in front of the camera: dirty, misted, frost-covered, snow-covered, damaged or covered by a sticker.–lane markings absent, worn, hidden (snow, mud) or multiple (roadworks, etc.);–close to the vehicle ahead (lane markings not detected);–roads that are narrow, winding, etc.In certain driving conditions (poor road surface or strong winds), the system may give alerts independent of the driver's level of vigilance.The following situations may interfere with the operation of the system or prevent it from working:–lane markings absent, worn, hidden (snow, mud) or multiple (roadworks),–close to the vehicle ahead (lane markings not detected),–roads that are narrow, winding, etc.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131