Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot Partner 2008-2018 Owner's Manual Ease of Use and Comfort Steering mounted controls - Speed limiter

64Steering mounted controlsPartner-2-VU_en_Chap04_Ergonomie_ed02-2016The speed of the vehicle responds to the pressure of the driver's foot, up to the the accelerator pedal's point of resistance, which indicates that the programmed speed has been reached.However, pressing the pedal beyond this point of resistance to the floor allows the programmed speed to be exceeded. To resume use of the limiter, simply reduce the pressure on the accelerator pedal gradually and return to a speed below that programmed.Adjustments canbe carried out when stationary, with the engine running, or with the vehicle moving.This speed limiter shows the function selection status in the instrument panel and displays the programmed speed:SPEEDLIMITER"LIMIT"Function selected,displaying of the "Speed Limiter" symbol.Function off,last programmed speed - OFF.Function on.Vehicle speed above,the programmed speed setting is displayed flashing.Operating fault detected,OFF - the dashes flash.1.Limiter mode On / Off.2.Reduce programmed speed setting.3.Increase programmed speed setting.4.Speed limiter On / Pause."This is the selected speed which the driver does not wish to exceed".This selection is made with the engine running while stationary or with the vehicle moving. The minimum speed which can be programmed is 20 mph (30 km/h).
65Steering mounted controlsEASE OF USE and COMFORT4Partner-2-VU_en_Chap04_Ergonomie_ed02-2016Selecting the functionProgramming a speed settingOn / OffTo memorise a speed higher than the previous one:-Press the SET + button.A brief press increases the speed by 1mph (km/h).A maintained press increases the speed in steps of 5 mph (km/h).To memorise a speed lower than the previous one.-Press the SET - button.A brief press decreases the speed by 1 mph (km/h).A maintained press decreases the speed in steps of 5 mph (km/h).-Place the switch in the LIMITposition. The limiter is selected but is not yet active. The screen indicates the last programmed speed setting.A speed can be programmed without activating the limiter but with the engine running.Pressing this button once activates the limiter, pressing the button again deactivates it (OFF).
66Steering mounted controlsPartner-2-VU_en_Chap04_Ergonomie_ed02-2016Switching the function offOperating faultThe programmed speed is cleared then replaced by three dashes.Contact a PEUGEOT dealer or a qualified workshop to have the system checked.Flashing of the speed settingGood practiceIn any event, the speed limiter cannot replace the need to observe speed limits, nor can it replace the need for vigilance on the part of the driver.Always pay attention to the profile of the road and sharp acceleration and stay in complete control of your vehicle.To avoid any jamming under the pedals:-ensure that the mat and its fixings on the floor are positioned correctly,-never place one mat on top of another.Exceeding the programmed speedPressing the accelerator pedal in order to exceed the programmed speed will have no effect unless you press the pedal firmly beyond the point of resistance.The limiter is deactivated temporarily and the programmed speed flashes accompanied by an audible signal.To return to the limiter function, reduce your speed to below the programmed speed.The speed setting flashes:-following forcing of the accelerator point of resistance,-when the limiter cannot prevent an increase in the vehicle speed due to the profile of the road or on a steep descent,-in the event of sharp acceleration.-Place the switch in position 0 or switch off the ignition to switch the system off.The last programmed speed remains in the memory.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131