Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot Partner 1996-2008 Owner's Manual Steering wheel controls Speed limiter

48 Steering wheel controls However, pressing the pedal beyond this point of resistance to the fl oor permits exceeding of the programmed speed. To resume use of the limiter, simply reduce the pressure on the accelerator pedal gradually and return to a speed below that programmed. The operating actions may be carried out when stationary, with the engine running, or with the vehicle moving. This speed limiter shows the function selection status on the instrument panel and displays the programmed speed: SPEED LIMITER "LIMIT" Function selected, displaying of the "Speed Limiter" symbol. Function deactivated, last programmed speed - OFF (example at 65 mph (107 km/h)). Function activated (example at 65 mph (107 km/h)). Vehicle speed above (example 70 mph (118 km/h)), the programmed speed is displayed fl ashing. Operating fault detected, OFF - the dashes fl ash. "This is the selected speed which the driver does not wish to exceed". This selection is made with the engine running while stationary or with the vehicle moving. The minimum speed which can be programmed is 20 mph (30 km/h). The speed of the vehicle responds to the pressure of the driver’s foot as far as the accelerator pedal point of resistance which indicates that the programmed speed has been reached.
49 Steering wheel controls 3 Selecting the function - Place the dial in the LIMIT position. The limiter is selected but is not yet active. The display indicates the last programmed speed. Programming a speed A speed can be programmed without activating the limiter but with the engine running. Activation/Deactivation (off) Pressing this button once activates the limiter, pressing the button again deactivates it (OFF). To memorise a speed higher than the previous one: - press the Set + button. A brief press increases the speed by 1 mph (km/h). A maintained press increases the speed in steps of 5 mph (km/h). To memorise a speed lower than the previous one: - press the Set - button. A brief press decreases the speed by 1 mph (km/h). A maintained press decreases the speed in steps of 5 mph (km/h).
50 Steering wheel controls Exceeding the programmed speed Pressing the accelerator pedal in order to exceed the programmed speed will have no effect unless you press the pedal fi rmly beyond the point of resistance . The limiter is deactivated temporarily and the programmed speed fl ashes. To return to the limiter function, reduce your speed to below the programmed speed. Switching the function off - Place the dial in position 0 or switch off the ignition to switch the system off. The last programmed speed remains in the memory. Operating fault The programmed speed is cleared then replaced by three dashes. Contact a PEUGEOT dealer to have the system checked. Good practice Flashing of the speed The speed fl ashes: - following forcing of the accelerator point of resistance, - when the limiter cannot prevent an increase in the vehicle speed due to the profi le of the road or on a steep descent, - in the event of sharp acceleration. In any event, the speed limiter cannot replace the need to observe speed limits, nor can it replace the need for vigilance and responsibility on the part of the driver. Always pay attention to the profi le of the road and sharp acceleration and stay in complete control of your vehicle. To avoid any jamming under the pedals: - ensure that the mat and its fi xings on the fl oor are positioned correctly, - never place one mat on top of another.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131