Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot Partner 1996-2008 Owner's Manual Steering wheel controls Cruise control

45 Steering wheel controls ERGONOMICS and COMFORT3 CRUISE CONTROL "CRUISE" In order for it to be programmed or activated, the vehicle speed must be greater than 25 mph (40 km/h) with at least 4th gear engaged. This cruise control shows the function selection status on the instrument panel and displays the programmed speed: Function selected, displaying of the "Cruise Control" symbol. Function deactivated, OFF (example at 107 km/h). Function activated (example at 107 km/h). Vehicle speed above (e.g. 118 km/h), the programmed speed is displayed fl ashing. Operating fault detected, OFF - the dashes fl ash. "This is the speed at which the driver wishes to drive". This aid to driving in free-fl owing traffi c enables the vehicle to maintain the speed programmed by the driver, unless a steep gradient makes this impossible.
46 Steering wheel controls Selecting the function - Place the switch in the CRUISEposition. The cruise control is selected but is not yet active and no speed has been programmed. First activation/programming a speed - Reach the chosen speed by pressing the accelerator. - Press the SET -or SET + button. This programmes/activates the reference speed and the vehicle will maintain this speed. Temporary exceeding of the speed It is possible to accelerate and drive momentarily at a speed greater than the programmed speed. The value programmed fl ashes. When the accelerator pedal is released, the vehicle will return to the programmed speed. Deactivation (off) - Press this button or the brake or clutch pedal. Reactivation - Following deactivation of the cruise control, press this button. Your vehicle will return to the last programmed speed. Alternatively, you can repeat the "fi rst activation" procedure.
47 Steering wheel controls ERGONOMICS and COMFORT3 Changing the programmed speed There are two methods of memorising a speed higher than the previous one: Switching the function off Operating fault The programmed speed is cleared then replaced by three dashes. Contact a PEUGEOT dealer to have the system checked. Cancelling the programmed reference speed When the vehicle becomes stationary, after switching off the ignition, the system no longer memorises a speed. Without using the accelerator: - press the Set + button. A brief press increases the speed by 1 mph (km/h). A maintained press increases the speed in steps of 5 mph (km/h). Using the accelerator: - exceed the memorised speed until the speed required is reached, - press the Set + or Set - button. To memorise a speed lower than the previous one: - press the Set - button. A brief press decreases the speed by 1 mph (km/h). A maintained press decreases the speed in steps of 5 mph (km/h). - Place the dial in position 0 or switch off the ignition to switch everything off. Good practice When changing the programmed reference speed by means of a maintained press, pay attention as the speed can increase or decrease rapidly. Do not use the cruise control on slippery roads or in heavy traffi c. In the event of a steep slope, the cruise control cannot prevent the vehicle from exceeding the programmed speed. In any event, the cruise control cannot replace the need to observe the speed limits, nor can it replace the need for vigilance and responsibility on the part of the driver. It is advisable to leave your feet near the pedals. To avoid any jamming under the pedals: - ensure that the mat and its fi xings on the fl oor are positioned correctly, - never place one mat on top of another.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131