Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot 5008 2009-2016 Owner's Manual Monitoring

Monitoring145008_en_Chap01_controle-marche_ed01-2015Instrument panelsPanel grouping together the vehicle operation indication dials and warning lamps.Instruments1.Rev counter.Indicates the engine speed (x 1 000 rpm).2.Coolant temperaturegauge.Indicates the temperature of the engine coolant (° Celsius).3.Fuel level.Indicates the quantity of fuel remaining in the tank.4.Speedometer.Indicates the current speed of the moving vehicle (mph or km/h).5.Screen.6.Control switch.Temporary display of the service indicator and driving range with the AdBlue®additive. Display and reset the selected function (trip distance recorder or service indicator).7.Instrument panel lighting dimmer.Adjusts the brightness of the lighting of the instruments and controls, if the vehicle lighting is on.For more information, refer to the section corresponding to the button or function and its associated display.
1Monitoring155008_en_Chap01_controle-marche_ed01-2015Screen(s)A.Speed limiterorCruise control.(mph or km/h)B.Trip distance recorder.(miles or km)C.Service indicator.(miles or km) or,Engine oil level indicator (depending on version).ordistance recorder.(miles or km)D.Gear shift indicator.Electronic or automatic gearbox.E.Warning messages and function status messages, trip computer, GPS navigation information.
Monitoring165008_en_Chap01_controle-marche_ed01-2015Left-hand direction indicatorflashing with buzzer.The lighting stalk is pushed down.Right-hand direction indicatorflashing with buzzer.The lighting stalk is pushed up.Operation indicator lampsIf one of the following indicator lamps comes on, this confirms that the corresponding system has come into operation.Warning lampis onCauseAction / ObservationsSidelampsfixed.The lighting stalk is in the "Sidelamps" position.Indicator and warning lampsWhen the ignition is switched onCertain warning lamps come on for a few seconds when the vehicle's ignition is switchedon.When the engine is started, these same warning lamps should go off.If they remain on, before moving off, refer to the information on the warning lamp concerned.Associated warningsThe illumination of certain warning lamps may be accompanied by an audible signal and a message in the multifunction screen.Visual indicators informing the driver that a system is in operation (operation or deactivation indicator lamps) or of the occurrence of a fault (warning lamp).The warning lamps may come on continuously (fixed) or flash.Certain warning lamps may come on in one of two different modes. Only by relating the type of illumination to the operating status of the vehicle can it be ascertained whether the situation is normal or whether a fault has occurred.
1Monitoring175008_en_Chap01_controle-marche_ed01-2015Diesel engine pre-heatingfixed.The ignition switch is at the 2ndposition (ignition on).Wait until the warning lamp has switched off before starting.The duration for which the warning lamp is on is determined by the climatic conditions.Dipped beam headlampsfixed.The lighting stalk is in the "Dipped beam headlamps" position.Main beam headlampsfixed.The lighting stalk is pulled towards you.Pull the stalk to return to dipped beam headlamps.Front foglampsfixed.The front foglamps are switched on using the ring on the lighting control stalk.Turn the ring on the lighting control stalk rearward twice to switch off the front foglamps.Rear foglampsfixed.The rear foglamps are on.Turn the ring on the stalk rearward to switch off the rear foglamps.Electric parking brakefixed.The electric parking brake is applied.Release the electric parking brake to switch off the warning lamp: with your foot on the brake pedal, pull the electric parking brake control lever.Observe the safety recommendations.For more information on the electric parking brake, refer to the corresponding section.Warning lampis onCauseAction / Observations
Monitoring185008_en_Chap01_controle-marche_ed01-2015Warning lampis onCauseAction / ObservationsDeactivation of the automatic functions of the electric parking brakefixed.The "automatic application" (on switching off the engine) and "automatic release" functions are deactivated or faulty.Activate the function (depending on the country of sale) via the vehicle configuration menu or contact a PEUGEOT dealer or a qualified workshop if automatic application / release is not possible.For more information on the electric parking brake, refer to the corresponding section.Foot on the brake pedalfixed.The brake pedal is not pressed.You must press the brake pedal firmly to:-start the engine with an electronic gearbox (lever in position N),-manually release the parking brake.flashing.With an electronic gearbox, if you hold the vehicle on an incline using the accelerator for too long, the clutch overheats.Use the brake pedal and/or the electric parking brake.Parking space sensorsfixed.The parking space sensors function is active.Press the corresponding button to deactivate it.flashing.The system is measuring the space.Once the measurement has been done, the warning lamp comes on fixed again.Stop & Startfixed.When the vehicle stops (red lights, traffic jams, ...) the Stop & Start system has put the engine into STOP mode.The warning lamp goes off and the engine restarts automatically in START mode, as soon as you want to move off.flashes for a few seconds, then goes off.STOP mode is temporarily unavailable.orSTART mode is invoked automatically.For more information on Stop & Start, refer to the corresponding section.
1Monitoring195008_en_Chap01_controle-marche_ed01-2015Deactivation indicator lampsIf one of the following indicator lamps comes on, this confirms that the corresponding system has been switched off intentionally.This is may be accompanied by an audible signal and a message on the multifunction screen.Warning lampis onCauseAction / ObservationsPassenger's airbag systemfixed.The control, located in the glove box, is set to the OFF position.The passenger's front airbag is deactivated.You can install a "rearward facing" child seat, unless there is a fault with the operation of the airbags (Airbag warning lamp on).Set the control to the ON position to activate the passenger's front airbag.In this case, do not fit a child seat in the rearward facing position.Warning lampsWhen the engine is running or the vehicle is being driven, the illumination of one of the following warning lamps indicates a fault which requires action on the part of the driver.Any fault resulting in the illumination of a warning lamp must be investigated further by reading the associated message in the multifunction screen.If you encounter any problems, do not hesitate to contact a PEUGEOT dealer or a qualified workshop.Warning lampis onCauseAction / ObservationsSTOPfixed, alone or associated with another warning lamp, accompanied by an audible signal and a message in the screen.Illumination of this warning lamp is associated with a serious fault with the braking system, power steering, engine lubrication system or cooling system.Stop as soon as it is safe to do so as there is a risk that the engine will cut out while driving.Park, switch off the ignition and contact a PEUGEOT dealer or a qualified workshop.
Monitoring205008_en_Chap01_controle-marche_ed01-2015Serviceon temporarily.A minor fault has occurred for which there is no specific warning lamp.Identify the fault by reading the message shown in the screen, such as, for example:-opening of the doors, boot or bonnet,-engine oil low level,-screenwash low level,-flat remote control battery,-saturation of the particle filter (Diesel)As soon as the traffic conditions permit, regenerate the filter by driving at a speed of at least 40 mph (60 km/h) until the service warning lamp goes off.-a fault with the tyre under-inflation detection system,-...For any other faults, contact a PEUGEOT dealer or a qualified workshop.fixed.A major fault has occurred for which there is no specific warning lamp.Identify the fault by reading the message shown on the screen and contact a PEUGEOT dealer or a qualified workshop.fixed, associated with the flashing and then fixed display of the service indicator spanner.The servicing interval has been exceeded.Only on BlueHDi Diesel versions.Your vehicle must be serviced as soon as possible.Warning lampis onCauseAction / Observations
1Monitoring215008_en_Chap01_controle-marche_ed01-2015Electric parking brakeflashing.The electric parking brake is not applied automatically.The application/release is faulty.You must stop as soon as it is safe to do so.Park on flat level ground, engage a gear (or place the lever in position P for an automatic gearbox), switch off the ignition and contact a PEUGEOT dealer or a qualified workshop.Electric parking brake faultfixed.The electric parking brake has a fault.Contact a PEUGEOT dealer or a qualified workshop without delay.For more information on the electric parking brake, refer to the corresponding section.Warning lampis onCauseAction / ObservationsBrakingfixed, associated with the STOP warning lamp.The braking system fluid level has dropped significantly.You must stop as soon as it is safe to do so.Top up with brake fluid recommended by PEUGEOT.If the problem persists, have the system checked by a PEUGEOT dealer or a qualified workshop.+fixed, associated with the electric parking brake malfunction warning lamp, if the parking brake is released.The braking system has a fault.You must stop as soon as it is safe to do so.Park, switch off the ignition and contact a PEUGEOT dealer or a qualified workshop.+fixed, associated with the STOP and ABS warning lamps.The electronic brake force distribution (EBFD) system has a fault.You must stop as soon as it is safe to do so.Have it checked by a PEUGEOT dealer or a qualified workshop.Anti-lock Braking System (ABS)fixed.The anti-lock braking system has a fault.The vehicle retains conventional braking.Drive carefully at reduced speed and contact a PEUGEOT dealer or a qualified workshop without delay.
Monitoring225008_en_Chap01_controle-marche_ed01-2015Warning lampis onCauseAction / ObservationsEngine autodiagnosis systemflashing.The engine management system has a fault.Risk of destruction of the catalytic converter.Have it checked by a PEUGEOT dealer or a qualified workshop.fixed.The emission control system has a fault.The warning lamp should go off when the engine is started.If it does not go off, contact a PEUGEOT dealer or qualified workshop without delay.Low fuel levelfixed with the needle in the red zone.When it first comes on there remains approximately 6 litres of fuel in the tank.At this point, you begin to use the fuel reserve.Refuel as soon as possible to avoid running out of fuel.This warning lamp will come on every time the ignition is switched on, until a sufficient addition of fuel is made.Fuel tank capacity: approximately 60 litres.Never continue to drive until you run out of fuel, as this could damage the emission control and injection systems.Maximum coolant temperaturefixed with the needle in the red zone.The temperature of the cooling system is too high.Stop as soon as it is safe to do so.Wait until the engine has cooled down before topping up the level, if necessary.If the problem persists, contact a PEUGEOT dealer or a qualified workshop.Dynamic stability control(DSC/ASR)flashing.The DSC/ASR regulation is operating.The system optimises traction and improves the directional stability of the vehicle in the event of loss of grip or trajectory.fixed.The DSC/ASR system has a fault.Have it checked by a PEUGEOT dealer or a qualified workshop.
1Monitoring235008_en_Chap01_controle-marche_ed01-2015AdBlue® additive(BlueHDi Diesel)fixed, on switching on the ignition, accompanied by an audible signal and a message indicating the remaining driving range.The remaining driving range is between 350 miles (600 km) and 1500 miles (2400 km).Have the AdBlue® additive tank topped up as soon as possible: go to a PEUGEOT dealer or a qualified workshop, or carry out this operation yourself.+flashing associated with the SERVICE warning lamp, accompanied by an audible signal and a message indicating the remaining driving range.The remaining driving range is between 0 and 350 miles (600 km).You must top-up the AdBlue® additive tank to avoid a breakdown: go to a PEUGEOT dealer or a qualified workshop, or carry out this operation yourself.flashing, associated with the SERVICE warning lamp, accompanied by an audible signal and a message indicating that starting is prevented.The AdBlue® tank is empty: the starting inhibition system required by legislation prevents starting of the engine.To be able to start the engine, you must top-up theAdBlue® additive tank: go to a PEUGEOT dealer or a qualified workshop, or carry out this operation yourself.It is essential to add at least 3.8 litres of AdBlue® to the additive tank.Warning lampis onCauseAction / ObservationsFor topping-up or for more information on the AdBlue® additive, refer to the corresponding section.
Monitoring245008_en_Chap01_controle-marche_ed01-2015Warning lampis onCauseAction / Observations++SCR emissions control system(BlueHDi Diesel)fixed, on switching on the ignition, associated with the SERVICE and engine diagnostic warning lamps, accompanied by an audible signal and a message.A fault with the SCR emissions control system has been detected.This alert disappears once the exhaust emissions return to normal levels.flashing, on switching on the ignition, associated with the SERVICE and engine diagnostic warning lamps, accompanied by an audible signal and a message indicating the remaining driving range.After confirmation of the fault with the emissions control system, you can drive for up to 650 miles (1 100 km) before the engine starting inhibition system is triggered.Contact a PEUGEOT dealer or a qualified workshop without delay, to avoid a breakdown.flashing, on switching on the ignition, associated with the SERVICE and engine diagnostic warning lamps, accompanied by an audible signal and a message.You have exceeded the authorised driving limit following confirmation of a fault with the emissions control system: the engine starting inhibition system prevents starting of the engine.To be able to start the engine, you must call on a PEUGEOT dealer or a qualified workshop.
1Monitoring255008_en_Chap01_controle-marche_ed01-2015Engine oil pressurefixed.There is a fault with the engine lubrication system.You must stop as soon it is safe to do so.Park, switch off the ignition and contact a PEUGEOT dealer or a qualified workshop.Battery charge*fixed.The battery charging circuit has a fault (dirty or loose terminals, slack or cut alternator belt, ...).The warning lamp should go off when the engine is started.If it does not go off, contact a PEUGEOT dealer or a qualified workshop.Warning lampis onCauseAction / ObservationsFront seat belt not fastened / unfastenedfixed then flashing accompanied by an increasing audible signal.The driver and/or the front passenger has not fastened or has unfastened their seat belt.Pull the strap then insert the tongue in the buckle.Rear seat belt not fastened / unfastenedfixed then flashing accompanied by an audible signal.One or more rear passengers have unfastened their seat belt.Door(s) openfixed if the speed is below 6 mph (10 km/h).A door, the boot, the lower tailgate or the bonnet (with alarm only) is still open.Close the door or boot.fixed and accompanied by an audible signal if the speed is above 6 mph (10 km/h).* Depending on the country of sale.
Monitoring265008_en_Chap01_controle-marche_ed01-2015Warning lampis onCauseAction / ObservationsDirectional headlampsflashing.The directional headlamps system has a fault.Have it checked by a PEUGEOT dealer or a qualified workshop.Under-inflationfixed.The pressure in one or more wheels is too low.Check the pressure of the tyres as soon as possible.This check should preferably be carried out when the tyres are cold.+flashing then fixed, accompanied by the Service warning lamp.The tyre pressure monitoring system has a fault or no sensor is detected on one of the wheels.Under-inflation detection is not assured.Have the system checked by a PEUGEOT dealer or a qualified workshop.Airbagstemporarily.This lamp comes on for a few seconds when you turn on the ignition, then goes off.This lamp should go off when the engine is started.If it does not go off, contact a PEUGEOT dealer or a qualified workshop.fixed.One of the airbag or seat belt pretensioner systems has a fault.Have it checked by a PEUGEOT dealer or a qualified workshop.Water in Dieselfixed.The Diesel fuel filter contains water.Risk of damage to the injection system on Diesel engines.Contact a PEUGEOT dealer or a qualified workshop without delay.
1Monitoring275008_en_Chap01_controle-marche_ed01-2015Coolant temperature indicatorWith the engine running, when the needle is:-in zone A, the temperature is correct,-in zone B, the temperature is too high; the max temperature warning lamp 1 and the central STOP warning lamp come on, accompanied by an audible signal and a message in the screen.After driving for a few minutes, the temperature and pressure in the cooling system increase.To top up the level:Fwait for the engine to cool,Funscrew the cap by two turns to allow the pressure to drop,Fwhen the pressure has dropped, remove the cap,Ftop up the level to the "MAX" mark.You must stop as soon as it is safe to do so.Wait a few minutes before switching off the engine.Contact a PEUGEOT dealer or a qualified workshop.
Monitoring285008_en_Chap01_controle-marche_ed01-2015Service indicatorBetween 600 miles (1 000 km) and 1 800 miles (3 000 km) remain before the next service is dueFor 5 seconds after the ignition is switched on, the spanner symbolising the service operations comes on. The distance recorder display line indicates the distance remaining before the next service is due.Example: 1 700 miles (2 800 km) remain before the next service is due.For 5 seconds after the ignition is switched on, the screen indicates:5 seconds after the ignition is switched on, the spanner goes off; the distance recorder resumes its normal operation. The screen then indicates the total and trip distances.Less than 600 miles (1 000 km) remain before the next service is dueExample: 560 miles (900 km) remain before the next service is due.For 5 seconds after the ignition is switched on, the screen indicates:5 seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on to indicate that a service must be carried out soon.More than 1 800 miles (3 000 km) remain before the next service is dueWhen the ignition is switched on, no service information appears in the screen.System which informs the driver when the next service is due, in accordance with the manufacturer's servicing schedule.The point at which the service is due is calculated from the last indicator zero reset, according to the mileage covered since the last service.For BlueHDi Diesel versions, depending on the country of sale, the level of deterioration of the engine oil may also be taken into account.
1Monitoring295008_en_Chap01_controle-marche_ed01-2015Resetting the service indicatorIf you have carried out the service on your vehicle yourself:Fswitch off the ignition,Fpress and hold the trip distance recorder zero reset button,Fswitch on the ignition; the distance recorder display begins a countdown,Fwhen the display indicates "=0", release the button; the spanner disappears.Service overdueFor 5 seconds after the ignition is switched on, the spanner flashes to indicate that the service must be carried out as soon as possible.Example: the service is overdue by 186 miles (300 km).5 seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on.Retrieving the service informationYou can access the service information at any time.FPress the trip distance recorder zero reset button.The service information is displayed for a few seconds, then disappears.If you have to disconnect the battery following this operation, lock the vehicle and wait at least five minutes for the reset to be registered.After each service, the service indicator must be reset to zero.For BlueHDi versions, the spanner may also come on early, according to the level of deterioration of the engine oil, which depends on the driving conditions in which the vehicle is used.With BlueHDi Diesel versions, the Service warning lamp also comes on when the ignition is switched on.For 5 seconds after the ignition is switched on, the screen indicates:
Monitoring305008_en_Chap01_controle-marche_ed01-2015Engine oil level indicator*On versions fitted with an electric oil level indicator, the state of the engine oil level is displayed in the instrument panel for a few seconds when the ignition is switched on, after the service information.Oil level correctOil level lowOil level indicator faultIn the event of a fault with the electric indicator, the engine oil level is no longer monitored.When the system has a fault, you should check the engine oil level using the manual dipstick (located under the bonnet).This is signalled by the flashing of "OIL", or the display of a message "Oil level incorrect" in the instrument panel, accompanied by illumination of the service warning lamp and an audible signal.If the low oil level is confirmed by a check using the dipstick, the level must be topped up to prevent damage to the engine.Refer to the "Checking levels" section.This is signalled by the flashing of "OIL--" or the display of a message "Oil level measurement invalid" in the instrument panel. Contact a PEUGEOT dealer or a qualified workshop.The level shown will only be correct if the vehicle is on level ground and the engine has been off for more than 30 minutes.* Depending on version.Refer to the "Checking levels" section.
1Monitoring315008_en_Chap01_controle-marche_ed01-2015Distance recordersThe total and trip distances are displayed for thirty seconds when the ignition is switched off, when the driver's door is opened and when the vehicle is locked or unlocked.Lighting dimmerSystem for manual adjustment of the brightness of the instrument panel in relation to the exterior brightness.Total distance recorderIt measures the total distance travelled by the vehicle since its first registration.Trip distance recorderIt measures the distance travelled since it was reset to zero by the driver.Dimmer deactivatedWhen the lighting is off, or in day mode on vehicles fitted with daytime running lamps, pressing the button does not have any effect.OperationWhen the vehicle lighting is on:Fpress the button to change the brightness of the instrument panel,Fwhen the lighting reaches the minimum setting, release the button, then press again to increase it,orFwhen the lighting reaches the maximum setting, release the button, then press again to reduce it,Fwhen the lighting reaches the level of brightness required, release the button.When the vehicle lighting is on, you cannot switch the instrument panel lighting off but you can adjust it to minimum.When travelling abroad, you may have to change the units of distance: the display of road speed must be in the official units (miles or km) for the country. The change of units is done via the screen configuration menu, with the vehicle stationary.FWith the ignition on, press the button until zeros appear.
Monitoring325008_en_Chap01_controle-marche_ed01-2015This displays the following information:-time,-date,-ambient temperature* (this flashes if there is a risk of ice),-alert messages,-trip computer (refer to the end of the section).Warning messages (e.g.: "Emission control system faulty") or information messages (e.g.: "Boot open") may appear temporarily. Some can be cleared by pressing the"ESC"button.Monochrome screen A (without audio equipment)ControlsMain menuThere are three display control buttons:-"ESC" to abandon the operation in progress,-"MENU" to scroll through the menus or sub-menus,-"OK" to select the menu or sub-menu required.FPress the "MENU" button to scroll through the various menus of the main menu:-vehicle configuration,-options,-display settings,-languages,-units.FPress the "OK" button to select the menu required.* With air conditioning only.Displays in the screen
1Monitoring335008_en_Chap01_controle-marche_ed01-2015Vehicle configurationOptionsOnce the "Options" menu has been selected, you can start diagnostics of the status of the equipment (active, not active, faulty).LanguagesOnce the "Languages" menu has been selected, you can change the language used by the display (Français, Italiano, Nederlands, Portugues, Portugues-Brasil, Türkçe, Deutsch, English, Espanol).Date and timeOnce the "Display settings" menu has been selected, you have access to the following settings:-year,-month,-day,-hour,-minutes,-12 or 24 hour mode.UnitsOnce the "Units" menu has been selected, you can change the units for:-temperature (°C or °F),-fuel consumption (l/100 km, mpg or km/l).FOnce you have selected a setting, press the "OK" button to change its value.FWait for approximately ten seconds without any action to allow the changed data to be recorded or press the "ESC" button to cancel.The screen then returns to the normal display.Once the "Vehicle configuration" menu has been selected, you can activate or deactivate the following equipment:-wiper linked with reverse gear (refer to the "Visibility" section),-selective unlocking (refer to the "Access" section),-"guide-me-home" lighting (refer to the "Visibility" section),-directional headlamps (refer to the "Visibility" section),-automatic parking brake** (refer to the "Driving" section),-parking space sensors (refer to the "Driving" section),-...As a safety measure, configuration of the multifunction screen by the driver must only be done when stationary.** Depending on the country of sale.
Monitoring345008_en_Chap01_controle-marche_ed01-2015Monochrome screen A (with audio equipment)ControlsThis displays the following information:-time,-date,-ambient temperature* (this flashes if there is a risk of ice),-alert messages,-audio sources (radio, CD, ...),-trip computer (refer to the corresponding section).Warning messages (e.g.: "Emission control system faulty") or information messages (e.g.: "Boot open") may appear temporarily. Some can be cleared by pressing the "<] arrow"button.Main menuFPress the "MENU" button for access to the main menu, then press the "5" or "6" buttons to scroll through the various menus:-radio-CD,-vehicle configuration,-options,-display settings,-languages,-units.FPress the "OK" button to select the menu required.From the audio equipment control panel, you can:Fpress the "MENU" button to gain access to the main menu,Fpress the "5" or "6" buttons to scroll through the items on the screen,Fpress the "MODE" button to change the permanent application (trip computer, audio source, ...),Fpress the "7" or "8" buttons to change a setting value,Fpress the "OK" button to confirm,orRadio-CDWith the audio equipment switched on, once the "Radio-CD" menu has been selected you can activate or deactivate the functions linked with use of the radio (RDS, REG), the CD or the CD changer (introscan, shuffle, CD repeat).Fpress this button to abandon the operation in progress.* With air conditioning only.For more information on the "Radio-CD" application, refer to the "Audio equipment and telematics" section.Displays in the screen
1Monitoring355008_en_Chap01_controle-marche_ed01-2015Date and timeOnce the "DATE AND TIME" menu has been selected, you have access to the following settings:-year,-month,-day,-hour,-minutes,-12 or 24 hour mode.LanguagesOnce the "Languages" menu has been selected, you can change the language used by the display.UnitsOnce the "Units" menu has been selected, you can change the units of the following parameters:-temperature (°C or °F),-fuel consumption (l/100 km, mpg or km/l).FOnce you have selected a setting, press the "7" or "8" buttons to change its value.FPress the "5" or "6" buttons to switch respectively to the previous or next setting.FPress the "OK" button to record the change and return to the normal display or press the "<] arrow" button to cancel.Vehicle configurationOnce the "Vehicle Configuration" menu has been selected, you can activate or deactivate the following equipment:-wiper linked with reverse gear (refer to the "Visibility" section),-selective unlocking (refer to the "Access" section),-guide-me-home lighting (refer to the "Visibility" section),-directional headlamps (refer to the "Visibility" section),-automatic parking brake** (refer to the "Driving" section),-...OptionsOnce the "Options" menu has been selected, you can start diagnostics of the status of the equipment (active, not active, faulty).As a safety measure, configuration of the multifunction screen by the driver must only be done when stationary.** Depending on the country of sale.
Monitoring365008_en_Chap01_controle-marche_ed01-2015Monochrome screen C (with PEUGEOT Connect Sound (RD5))Main menuDisplays according to context:-time,-date,-ambient temperature with air conditioning (the value displayed flashes if there is a risk of ice),-audio functions,-trip computer (see the corresponding section),-alert messages,-screen and vehicle equipment parameter setting menus."Audio functions" menuControlsFrom the audio equipment control panel, you can:Fpress the "MENU" button for access to the main menu,Fpress the "5" or "6" buttons to scroll through the items on the screen,Fpress the "MODE" button to change the permanent application (trip computer, audio source...),Fpress the "7" or "8" buttons to change a setting value,Fpress the "OK" button to confirm,orFPress the "MENU" button for access to the main menu:-audio functions,-trip computer (see the corresponding section),-personalisation-configuration,-telephone (Bluetooth system).With the audio equipment switched on, once this menu has been selected you can activate or deactivate the functions linked with use of the radio (RDS, REG, RadioText) or CD (introscan, shuffle, CD repeat).Fpress this button to abandon the operation in progress.FPress the"5" or "6" button to select the menu required, then confirm by pressing the "OK" button.For more information on the "Audio functions" application, refer to the PEUGEOT Connect Sound (RD5) section.Displays in the screen
1Monitoring375008_en_Chap01_controle-marche_ed01-2015"Trip computer" menuAlert logThis summarises the active warning messages, displaying them in succession in the multifunction screenStatus of functionsThis summarises the status of the functions present on the vehicle.FPress the "MENU" button to gain access to the general menu.FPress the arrows, then the "OK" button to select the "Trip computer" menu.Once this menu has been selected, you can consult information concerning the status of the vehicle (alert log, status of the functions...).Define the vehicle parametersOnce this menu has been selected, you can activate or deactivate the following equipment:-wiper linked with reverse gear (refer to the "Visibility" section),-selective unlocking (refer to the "Access" section),-guide-me-home lighting (refer to the "Visibility" section),-directional headlamps (refer to the "Visibility" section),-automatic parking brake* (refer to the "Driving" section),-..."Personalisation-Configuration" menuOnce this menu has been selected, you can gain access to the following functions:-define the vehicle parameters,-display configuration,-choice of language.FIn the "Trip computer" menu, select one of the applications.This allows you to enter an approximate value for the distance to the final destination.Enter the distance to the destination* Depending on the country of sale.
Monitoring385008_en_Chap01_controle-marche_ed01-2015Display configurationOnce this menu has been selected, you have access to the following settings:-brightness-video setting,-date and time setting,-selection of the units.Adjusting the date and timeFPress the "7" or "8" button to select the "Display configuration" menu, then the "OK" button.FPress the "5" or "6" button, to select the "Adjust date and time" line, then on the "OK" button.FPress the "7" or "8" button to select the setting to modify. Confirm by pressing the "OK"button then adjust the setting and confirm again to save the modification.Example: setting of the duration of the guide-me-home lighting.FPress the "5" or "6" buttons, then the "OK" button to select the menu required.FPress the "5" or "6" buttons, then the "OK" button to select the "Guide-me-home headlamps" line.FPress the "7" or "8" buttons to set the value required (15, 30 or 60 seconds), then press the "OK" button to confirm.FPress the "5" or "6" buttons, then the "OK" button to select the "OK" box and confirm or press the "<] arrow" button to cancel."Telephone" menuWith the audio equipment switched on, once this menu has been selected you can configure your Bluetooth hands-free kit (pairing), consult the various telephone directories (calls log, services...) and manage your communications (accept call, end call, call on hold, secret mode...).For more information on the telephone application, refer to the PEUGEOTConnect Sound (RD5) section.As a safety measure, configuration of the multifunction screen by the driver must only be done when stationary.Choice of languageOnce this menu has been selected, you can change the screen display language.FAdjust the settings one by one, confirming with the "OK" button.FPress the "5" or "6" button, then the "OK"button to select the "OK" box and confirm, or the "Back" button to cancel.
1Monitoring395008_en_Chap01_controle-marche_ed01-201516/9 retractable colour screen (PEUGEOT Connect Navigation (RT6))* For more information on these applications, refer to the "Audio equipment and telematics" section.Displays in the screenDepending on the context, it displays the following information:-time,-date,-altitude,-ambient temperature (the value displayed flashes if there is a risk of ice),-parking sensor information,-parking space measurement,-audio functions,-directory and telephone information,-satellite navigation system information,-settings menus for the screen, the satellite navigation system and vehicle systems.-the image from the reversing camera.ControlsFrom the navigation system control panel, to select one of the applications:Fpress the dedicated "RADIO", "MUSIC", "NAV", "TRAFFIC", "PHONE" or "SETUP" button for access to the corresponding menu,Fturn the dial A to select a function, an item in a list,Fpress button B to confirm the selection,orFpress the "Back" button to abandon the current operation and return to the previous display.With repeated presses on the C"MODE"button, the screen displays:-"RADIO / MEDIA"*,-"TELEPHONE"*,-"FULL SCREEN MAP"*,-"MAP IN A WINDOW"*,"SETUP" menuFPress the "SETUP" button to open the configuration menu:-"Display configuration",-"Speech synthesis setting".-"Select language",-"Define vehicle parameters",-"Alert log".For the operation of the retractable screen (opening, closing, adjusting the position...), refer to the "Access to the retractable screen" section.As a safety measure, configuration of the multifunction screen by the driver must only be done when stationary.
Monitoring405008_en_Chap01_controle-marche_ed01-2015Display configurationThis menu is used to select the colour scheme for the screen, adjust the brightness, set the date and time and to choose the units for distance (km or miles), fuel consumption (l/100 km, mpg or km/l) and temperature (°Celsius or °Fahrenheit).Adjusting the voice synthesiserThis menu is used to adjust the volume setting for navigation instructions and to choose the type of voice (male or female).Choice of languageThis menu is used to choose the language used by the screen from a defined list.Vehicle parametersThis menu is used to activate or deactivate certain driving and comfort systems, classified by category:-"Driver aid":●"Electric brake*" (Automatic electric parking brake; refer to the "Driving" section),-"Wiper operation":●"Rear wiper operates in reverse: ON/ OFF" (rear wiper coupled to reverse gear; refer to the "Visibility" section),-"Vehicle access" (refer to the "Access" section):●"Plip action: all doors, driver only" (Selective unlocking of the driver's door),-"Lighting configuration" (refer to the "Visibility" section):●"Duration of guide me home lighting: OFF / 15 s / 30 s / 60 s" (Automatic guide me home lighting),●"Directional headlights: ON / OFF" (Main / additional directional lighting).Alert logThis lists the active alerts by displaying in turn the different messages associated with them.* Depending on the country of sale.Adjusting the date and time-Press on SETUP.-Select "Display configuration" and confirm.-Select "Set date and time" and confirm.Select "Minute adjustment via GPS" so that the minutes are adjusted automatically by satellite reception.-Select the setting to modify. Confirm by pressing on OK, then modify the setting and confirm again to save the modification.-Adjust the settings one by one.-Select "OK" in the screen then confirm to save the setting.
1Monitoring415008_en_Chap01_controle-marche_ed01-2015The screen opens automatically when the ignition is switched on. It closes automatically three seconds after switching off the ignition if the audio and telematics system is switchedoff.You can open or close the screen at any time, with the ignition on, using control A.-Press button A: the screen folds.-Press button A again: the screen opens again.Adjusting the angle of the screenIf you have closed the screen, it will open again automatically:-on switching on the audio and navigation system (unless it had been closed manually while the system was in operation),-when an outgoing telephone call is made,-when a voice command is given,-when a warning message linked with the STOP warning lamp is displayed (PEUGEOT Connect Navigation (RT6)).Access to the retractable screenYou can adjust the angle of the screen to one of four defined positions, by repeated presses on the front or back of the control B. The position of the screen is memorised on closing.
Monitoring425008_en_Chap01_controle-marche_ed01-2015Trip computerWhen the range falls below 20 miles (30 km), dashes are displayed. After filling with at least 5 litres of fuel, the range is recalculated and is displayed when it exceeds 60 miles (100 km).A few definitionsCurrent fuel consumption(mpg or l/100 km or km/l)Calculated over the last few seconds.Average fuel consumption(mpg or l/100 km or km/l)Calculated since the last trip reset.Distance travelled(miles or km)Calculated since the last trip reset.Average speed(mph or km/h)Calculated since the last trip reset.Stop & Start time counter(minutes / seconds or hours / minutes)If your vehicle is fitted with Stop & Start, a time counter calculates the time spent in STOP mode during a journey. It resets to zero every time the ignition is switched on with the key.If dashes are displayed continuously while driving in place of the digits, contact a PEUGEOT dealer or a qualified workshop.This value may vary following a change in the style of driving or the relief, resulting in a significant change in the current fuel consumption.This function is only displayed from 20 mph (30 km/h).Range(miles or km)The distance which can still be travelled with the fuel remaining in the tank (related to the average fuel consumption over the last few miles (kilometres) travelled).
1Monitoring435008_en_Chap01_controle-marche_ed01-2015Trip computerFPress the button, located at the end of the wiper stalk, to display the various items of trip computer information in succession.The trip computer provides the following information:System that gives you information on the current journey (range, fuel consumption…).Monochrome screen AInformation displays-range,-current fuel consumption,-Stop & Start time counter,-distance travelled,-average fuel consumption,FPress the control for more than twoseconds to reset to zero the distance travelled, the average fuel consumption and the average speed.Trip resetFThe next press then returns you to the normal display.-average speed.
Monitoring445008_en_Chap01_controle-marche_ed01-2015Monochrome screen CInformation displaysInstrument panel screenTrip computerWith screen CFPress the PEUGEOT Connect Sound (RD5) "MODE" button repeatedly to display the trip comuter information.Then, repeatedly press the button on the end of the wiper control stalk to display each of the trip computer tabs in turn.OrFPress the button on the end of the wiper control stalk to temporarily display a window with the trip computer information.Then, repeatedly press the button on the end of the wiper control stalk to display each of the trip computer tabs in turn.With instrument panel screenFPress the button on the end of the wiper control stalk to display each of the trip computer tabs in turn.System which provides instantaneous information on the current trip (range, fuel consumption…).Depending on your vehicle's equipment, the trip computer information appears in the monochrome C screen or in the instrument panel screen.
1Monitoring455008_en_Chap01_controle-marche_ed01-2015-The trip "1" tab with:●the average speed, for the first trip,●the average fuel consumption,-The trip "2" tab with:●the average speed, for the second trip,●the average fuel consumption,With the instrument panel screen-A black screen.-A reminder of the navigation instructions with the PEUGEOT Connect Navigation (RT6) system.Press again to return to the current display.Trip reset-The current information with:●the range,●the current fuel consumption,●the distance remaining to be travelled or the Stop & Start time counter.With the C screen or instrument panel screenFWhen the trip required is displayed, press the control for more than two seconds.Trips "1" and "2" are independent but their use is identical.For example, trip "1" can be used for daily figures, and trip "2" for monthly figures.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131