Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot 3008 2016-2023 Lighting and visibility Wiper control stalk

80Lighting and visibilityThe camera detection range is between 15m (for pedestrians) and 200m, depending on visibility conditions.The image provided by the camera is displayed in shades of grey in the instrument panel; warm objects appear brighter than cold objects.If pedestrians or animals are detected, they appear in yellow frames.If the system detects a risk of collision with pedestrians or animals, it triggers an alert: one of these symbols appears on the instrument panel. The corresponding silhouette is framed in red.If the "Night Vision" display mode has not been selected, the alert is triggered in the form of a temporary window.In the event of an alert, the driver may act by making an avoiding manoeuvre or by braking.Operating limitsThe following situations may interfere with the operation of the system or prevent it from working:–Poor visibility conditions (falling snow, heavy rain, thick fog).–Camera masked by snow, mud or dust.–Camera scratched after going through roller car washes repeatedly.–Very high outside temperature.–At the top or bottom of a steep slope.–On a very winding road.–In a bend.–After an impact which may have impaired the camera settings or damaged it.–After repainting of the grille outside of the PEUGEOT dealer network or a qualified workshop.Maintenance recommendationsThe infrared camera has a wash nozzle connected to the vehicle’s front screenwash system.This nozzle operates every 5th use of the screenwash.Regularly check that the camera is clean.In bad weather, or in wintry conditions, ensure that the camera is not covered with mud, ice or snow.MalfunctionIf the event of a malfunction, this warning lamp comes on in orange on the instrument panel, accompanied by the display of a message.Have it checked by a PEUGEOT dealer or a qualified workshop.Wiper control stalkBefore operating the wipers in wintry conditions, clear any snow, ice or frost from the windscreen and around the wiper arms and blades.Do not operate the wipers on a dry windscreen. In extremely hot or cold weather, check that the wiper blades are not stuck to the windscreen before operating the wipers.After using an automatic car wash, you may temporarily notice abnormal noises and poorer wiping performance. You do not need to replace the wiper blades.Windscreen wipers►To select the wiping speed: raise or lower the stalk to the desired position.
81Lighting and visibility4Fast wiping (heavy rain) Normal wiping (moderate rain) Intermittent wiping (proportional to the vehicle’s speed)Switching offAutomatic wiping Refer to the corresponding section.Single wipe►Pull the stalk briefly towards you.In position 1 or 2, the wiping frequency is automatically reduced when the speed of the vehicle drops below 3mph (5km/h).When the speed is above 6mph (10km/h) again, the wiping frequency returns to the original frequency (fast or normal).If the ignition has been switched off with the windscreen wipers active, you must operate the control stalk again to reactivate wiping when the ignition is switched on again (unless the ignition was off for less than aminute).After switching off the ignition, a slight movement of the windscreen wipers to store them under the bonnet may occur.Windscreen wash►Pull the wiper control stalk towards you and hold.A final wiping cycle is performed when screenwashing ends.The windscreen wash jets are incorporated into the tip of each wiper arm.Screenwash fluid is sprayed along the length of the wiper blade. This improves visibility and reduces screenwash fluid consumption.To avoid damaging the wiper blades, do not operate the screenwash if the screenwash reservoir is empty.Only operate the screenwash if there is no risk of the fluid freezing on the windscreen and hindering visibility. During the winter period, use "very cold climate" rated products.Never top up with water.Rear wiper►Turn the ring to align the desired symbol with the marking.OffIntermittent wiping Screenwash-wipe Reverse gearWhen reverse gear is engaged, the rear wiper will come into operation automatically if the front windscreen wipers are operating.The settings are changed via the Driving/Vehicle touch screen menu.In the event of accumulation of snow or hard frost or if a bicycle carrier is fitted to a towing device, deactivate the automatic rear wiper via the vehicle configuration menu.Rear screenwash►Turn the ring all the way towards the dashboard and hold.The screenwash and the wiper operate for as long as the ring remains turned.A final wiping cycle is performed when screenwashing ends.Automatic windscreen wipersIn AUTO mode, the windscreen wipers operate automatically and adapt to the intensity of the rainfall.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131