Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot 3008 2016-2023 Lighting and visibility Automatic windscreen wipers

81Lighting and visibility4Fast wiping (heavy rain) Normal wiping (moderate rain) Intermittent wiping (proportional to the vehicle’s speed)Switching offAutomatic wiping Refer to the corresponding section.Single wipe►Pull the stalk briefly towards you.In position 1 or 2, the wiping frequency is automatically reduced when the speed of the vehicle drops below 3mph (5km/h).When the speed is above 6mph (10km/h) again, the wiping frequency returns to the original frequency (fast or normal).If the ignition has been switched off with the windscreen wipers active, you must operate the control stalk again to reactivate wiping when the ignition is switched on again (unless the ignition was off for less than aminute).After switching off the ignition, a slight movement of the windscreen wipers to store them under the bonnet may occur.Windscreen wash►Pull the wiper control stalk towards you and hold.A final wiping cycle is performed when screenwashing ends.The windscreen wash jets are incorporated into the tip of each wiper arm.Screenwash fluid is sprayed along the length of the wiper blade. This improves visibility and reduces screenwash fluid consumption.To avoid damaging the wiper blades, do not operate the screenwash if the screenwash reservoir is empty.Only operate the screenwash if there is no risk of the fluid freezing on the windscreen and hindering visibility. During the winter period, use "very cold climate" rated products.Never top up with water.Rear wiper►Turn the ring to align the desired symbol with the marking.OffIntermittent wiping Screenwash-wipe Reverse gearWhen reverse gear is engaged, the rear wiper will come into operation automatically if the front windscreen wipers are operating.The settings are changed via the Driving/Vehicle touch screen menu.In the event of accumulation of snow or hard frost or if a bicycle carrier is fitted to a towing device, deactivate the automatic rear wiper via the vehicle configuration menu.Rear screenwash►Turn the ring all the way towards the dashboard and hold.The screenwash and the wiper operate for as long as the ring remains turned.A final wiping cycle is performed when screenwashing ends.Automatic windscreen wipersIn AUTO mode, the windscreen wipers operate automatically and adapt to the intensity of the rainfall.
82Lighting and visibilityDetection is via a rain/brightness sensor, located at the top centre of the windscreen behind the rear view mirror.Do not cover the rain/sunshine sensor.When using an automatic car wash, switch off the automatic wipers and the ignition.In winter, wait until the windscreen is completely clear of ice before activating the automatic wipers.Switching on►Give a short downwards push to the control stalk.A wiping cycle confirms that the instruction has been accepted.This indicator lamp lights up on the instrument panel, accompanied by a message.Switching off►Give the control stalk another brief push downwards or place the control stalk in another position (Int, 1 or 2).This indicatorlamp goes off in the instrument panel, accompanied by a message.If the ignition has been off for more than one minute, the automatic wipers must be reactivated by pushing the control stalk downwards.MalfunctionIf a fault occurs with the automatic wipers, the wipers operate in intermittent mode.Have it checked by a PEUGEOT dealer or a qualified workshop.Special position of the windscreen wipersThis maintenance position is used while cleaning or replacing the wiper blades. It can also be useful, in wintry weather (ice, snow), to release the wiper blades from the windscreen.To maintain the effectiveness of the flat wiper blades, it is advisable to:–handle them with care.–clean them regularly using soapy water.–avoid using them to hold cardboard on the windscreen.–replace them at the first signs of wear.Before removing a windscreen wiper bladeOperating the wiper control stalk within one minute after switching off the ignition will place the wiper blades in a vertical position.►Proceed with the desired operation or the replacement of the wiper blades.After refitting a windscreen wiper blade►To return the wiper blades to their initial position after the operation, switch on the ignition and operate the wiper control stalk.
83Lighting and visibility4Changing a wiper bladeRemoving/Refitting at the front►Carry out these wiper blade replacement operations from the driver's side.►Starting with the wiper blade farthest from you, hold each arm by the rigid section and raise it as far as possible.Take care not to hold the arms at the jet locations.Do not touch the wiper blades - risk of irreparable deformation.Do not release them while moving them. Risk of damaging the windscreen!►Clean the windscreen using screenwash fluid.Do not apply "Rain X" type water-repellent products.►Unclip the worn wiper blade closest to you and remove it.►Install the new wiper blade and clip it to the arm.►Repeat the procedure for the other wiper blade.►Starting with the wiper blade closest to you, once again hold each arm by the rigid section, then guide it carefully onto the windscreen.Removing/refitting at the rear►Hold the arm by the rigid section and raise it as far as possible.►Clean the rear screen using screenwash fluid.►Unclip the worn wiper blade and remove it.►Install the new wiper blade and clip it to the arm.►Once again hold the arm by the rigid section, then guide it carefully onto the rear screen.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131