Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot 3008 2016-2023 Driving Stop & Start

127Driving6Stop & StartThe Stop & Start function puts the engine temporarily into standby - STOP mode - during phases when the vehicle is stationary (e.g.red lights, traffic jams). The engine automatically restarts - START mode - as soon as the driver indicates the intention of moving off again.Primarily designed for urban use, the function is intended to reduce fuel consumption and exhaust emissions as well as the noise level when stationary.The function does not affect the functionalities of the vehicle, in particular the braking.Deactivation/ReactivationThe function is activated by default when the ignition is switched on.The settings are changed via the Driving/Vehicle touch screen menu.A message on the instrument panel confirms the change of status.When the function is deactivated, if the engine was in standby, it restarts immediately.Associated indicator lampsFunction activated. Function deactivated or malfunction. Opening the bonnetBefore doing anything under the bonnet, deactivate the Stop & Start system to avoid any risk of injury caused by the engine restarting automatically.Driving on flooded roadsBefore entering into a flooded area, it is strongly recommended that you deactivate the Stop & Start system.For more information on Driving recommendations, particularly on flooded roads, refer to the corresponding section.OperationMain conditions for operation–The driver’s door must be closed.–The driver's seat belt must be fastened.–The level of charge in the battery must be sufficient.–The temperature of the engine must be within its nominal operating range.–The outside temperature must be between 0°C and 35°C.Putting the engine into standby (STOP mode)The engine automatically enters standby mode as soon as the driver indicates their intention to stop:–With a manual gearbox, at speeds below 2 mph (3 km/h) on 1.5 BlueHDi versions, or with the vehicle stationary on 1.2 PureTech versions, when you place the gear lever in neutral and release the clutch pedal.–With an automatic gearbox, at speeds below 12 mph (20 km/h) on BlueHDi versions, or with the vehicle stationary on other versions, when you depress the brake pedal or place the gear selector in mode N.Time counterA time counter adds up the time spent in standby during the journey. It is reset to zero every time the ignition is switched on.Special casesThe engine will not go into standby if the conditions for operation are not met and in the following cases:–Steep slope (ascending or descending).–Vehicle has not exceeded 6 mph (10km/h) since the last engine start.–Sport mode selected (depending on equipment).–Electric parking brake applied or being applied.–Needed to maintain a comfortable temperature in the passenger compartment.–Demisting active.In these cases, this indicator lamp flashes for a few seconds, then goes off.
128DrivingAfter the engine has restarted, STOP mode is not available until the vehicle has reached a speed of 5 mph (8km/h).During parking manoeuvres, STOP mode is not available for a few seconds after coming out of reverse gear or turning the steering wheel.Restarting the engine (START mode)The engine automatically restarts as soon as the driver indicates the intention of moving off again:With a manual gearbox: with the clutch pedal fully depressed.With an automatic gearbox:–With the selector in mode D or M: with the brake pedal released.–With the selector in mode N and the brake pedal released: with the selector at D or M.–With the selector in mode P and the brake pedal depressed: with the selector at R, N, Dor M.–With reverse gear engaged.Special casesThe engine will restart automatically if the conditions for operation are met again and in the following cases:–Vehicle speed exceeds 16 mph (25 km/h) with 2.0 BlueHDi versions with automatic gearbox in mode D, or 2 mph (3 km/h) with other versions.–The electric parking brake is being applied.–Deselecting the Sport mode (depending on equipment).In these cases, this indicator lamp flashes for a few seconds, then goes off.MalfunctionsIn the event of a fault with the system, this warning lamp flashes for a few moments on the instrument panel, then remains on, accompanied by the display of a message.Have it checked by a PEUGEOT dealer or a qualified workshop.The vehicle stalls in STOP modeAll of the instrument panel warning lamps come on if there is a fault.►Switch off the ignition then start the engine again with the key or the "START/STOP" button.12V batteryThe Stop & Start system requires a 12 V battery of specific technology and specification.All work must be carried out only by a PEUGEOT dealer or a qualified workshopTyre under-inflation detectionThis system alerts the driver if one or more tyres suffer a drop in pressure.The alert is raised when the vehicle is moving, not when stationary.It compares the information given by the wheel speed sensors with reference values, which must be reinitialised every time the tyre pressures are adjusted or a wheel changed.It takes into account the last values stored during the reinitialisation request. It is therefore essential that the tyre pressure is correct during the operation. This operation is the driver’s responsibility.The tyre under-inflation detection cannot, in any circumstances, replace the need for vigilance on the part of the driver.This system does not avoid the need to regularly check the tyre pressures (including the spare wheel), especially before a long journey.Driving with under-inflated tyres, particularly in adverse conditions (heavy load, high speed, long journey):–worsens road-holding.–lengthens braking distances.–causes premature wear of the tyres.–increases energy consumption.The inflation pressures defined for the vehicle can be found on the tyre pressure label.For more information on the Identification markings, refer to the corresponding section.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131