Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot 3008 2016-2023 Driving

111Driving6Driving recommendations►Observe the driving regulations and remain vigilant whatever the traffic conditions.►Monitor your environment and keep your hands on the wheel to be able to react to anything that may happen any time.►Drive smoothly, anticipate the need for braking and maintain a longer safety distance, especially in bad weather.►Stop the vehicle before performing operations that require sustained attention (e.g.settings).►During long trips, take a break every 2 hours.Important!Never leave the engine running in a closed space without sufficient ventilation. Internal combustion engines emit toxic exhaust gases such as carbon monoxide. Danger of poisoning and death!In very severe wintry conditions (temperature below -23°C), let the engine run for 4 minutes before moving off, to ensure the correct operation and durability of the mechanical components of your vehicle (engine and gearbox).Never drive with the parking brake applied. Risk of overheating and damaging the braking system!Never park the vehicle and never leave the engine running on a flammable surface (e.g.dry grass, dead leaves).The vehicle exhaust system is very hot, even several minutes after the engine stops. Risk of fire!Never drive on surfaces covered with vegetation (e.g.tall grass, accumulated dead leaves, crops, debris) such as a field, a country lane overgrown with bushes or a grassy verge.This vegetation could come into contact with the vehicle's exhaust systemor other systems which are very hot. Risk of fire!Make sure you do not leave any item in the passenger compartment which could act like a magnifying glass under the effect of the sun's rays and cause a fire. Risk of fire or damage to interior surfaces!Never leave the vehicle unattended, with the engine running. If you have to leave your vehicle with the engine running, apply the parking brake and put the gearbox into neutral or position N or P (depending on the type of gearbox).Never leave children inside the vehicle unsupervised.On flooded roadsWe strongly advise against driving on flooded roads, as this could cause serious damage to the internal combustion engine or electric motor, the gearbox and the electrical systems of the vehicle.If the vehicle absolutely must drive through a flooded section of road:►Check that the depth of the water does not exceed 15cm, taking account of waves that might be generated by other users.►Deactivate the Stop & Start function.►For rechargeable hybrid engines, place the mode selector in 4WD position (depending on version).►Drive as slowly as possible without stalling. In all cases, do not exceed 6 mph (10km/h).►Do not stop and do not switch off the engine.On leaving the flooded road, as soon as safety conditions allow, make several light brake applications to dry the brake discs and pads.If in doubt about the state of your vehicle, contact a PEUGEOT dealer or a qualified workshop.
112DrivingTowingDriving with a trailer places greater demands on the towing vehicle and particular care must be taken.Do not exceed the maximum towable weights.At altitude: reduce the maximum load by 10% per 1,000 metres of altitude; the lower air density at high altitudes decreases engine performance.New vehicle: do not tow a trailer until the vehicle has driven at least 620 miles (1,000 kilometres).If the outside temperature is high, let the engine idle for 1 to 2 minutes after the vehicle comes to a stop, to help it to cool.Before setting offNose weight►Distribute the load in the trailer so that the heaviest items are located as close as possible to the axle, and the nose weight (at the point where it joins your vehicle) approaches the maximum permitted, without exceeding it.Tyres►Check the tyre pressures of the towing vehicle and of the trailer, observing the recommended pressures.Lighting►Check the electrical signalling on the trailer and the headlamp beam height of your vehicle.If a genuine PEUGEOT towing device is used, the rear parking sensors will be deactivated automatically to avoid activating the audible signal.When drivingCoolingTowing a trailer uphill causes the coolant temperature to increase. The maximum towable load depends on the gradient and the exterior temperature. The fan’s cooling capacity does not increase with engine speed.►Reduce speed and lower the engine speed to limit the amount of heating produced.►Pay constant attention to the coolant temperature.If this warning lamp and the STOPwarning lamp come on, stop the vehicle and switch off the engine as soon as possible.BrakesUsing the engine brake is recommended to limit the overheating of the brakes. Braking distances are increased when towing a trailer.Side windBear in mind that the vehicle will be more susceptible to wind when towing.Anti-theft protectionElectronic immobiliserThe keys contain a code, which must be recognised by the vehicle before starting is possible.If the system malfunctions, indicated by the display of a message, the engine will not start.Contact a PEUGEOT dealer.Starting/Switching off the engineThe electronic key must be present in the passenger compartment.If the electronic key is not detected, a message is displayed.Move the electronic key so that the engine can be started or switched off.If there is still a problem, refer to the "Key not detected - Back-up starting or Back-up switch-off" section.
113Driving6Starting►With a manual gearbox, place the gear lever in neutral and fully depress the clutch pedal.►With an automatic gearbox, select modePorN and press the brake pedal.►Press the "START/STOP" button while maintaining pressure on the pedal until the engine starts.Diesel enginesIn negative temperatures and/or when the engine is cold, starting takes place only after the preheating warning lamp goes out.If this warning lamp comes on after pressing the "START/STOP" button:►Keep the pedal fully depressed and do not press the "START/STOP" button again until the engine is running.In all circumstances, if one of the starting conditions is not met, a message is displayed.In some circumstances, a message indicates that it is necessary to turn the steering wheel while pressing the "START/STOP" button to assist unlocking of the steering column.Petrol enginesWith Petrol engines, after a cold start, pre-heating the catalytic converter can cause noticeable engine vibrations, for anything up to 2 minutes (accelerated idle speed).If the engine stalls, release the clutch pedal and fully depress it again, the engine will restart automatically.Starting rechargeable hybrid vehicles►Fully depress the brake pedal and press the START/STOP button for approximately 2 seconds.►Keep your foot on the pedal until this indicator lamp comes on, indicating the activation of the rechargeable hybrid system (confirmed by an audible signal).To exit Park mode, wait for the READY indicator lamp to come on.By default, the system starts in Electric mode.Depending on certain parameters (battery charge level or outside temperature), the system determines whether it is necessary to start the petrol engine.It is possible to change the driving mode at any time using the mode selector.When the vehicle starts in electric mode, it makes no noise. Pay particular attention to pedestrians and cyclists who may not hear the vehicle coming despite the pedestrian horn.Switching off►Immobilise the vehicle using the parking brake.►With a manual gearbox, ideally put the gear lever into neutral.►With an automatic gearbox, ideally select modeP orN.►Press the "START/STOP" button.►For rechargeable hybrid vehicles, before leaving the vehicle, check that the READYindicator lamp is switched off.In some circumstances, it is necessary to turn the steering wheel to lock the steering column.On certain versions with an automatic gearbox (EAT6/EAT8), the steering column does not lock, but the gearbox locks in mode P.If the vehicle is not immobilised, the engine will not stop.With the engine off, the braking and steering assistance systems are also cut off - risk of loss of control of the vehicle!Never leave your vehicle with the electronic key still inside.
114DrivingSwitching on the ignition without starting the engineWith the electronic key in the passenger compartment, pressing the "START/STOP" button, without depressing any of the pedals, allows the ignition to be switched on without starting the engine (the instrument panel and accessories such as the audio system and the lighting will come on).►Press this button again to switch off the ignition and allow the vehicle to be locked.Key not detectedBack-up startingA back-up reader is fitted to the steering column, to enable the engine to be started if the system fails to detect the key in the recognition zone, or if the battery in the electronic key is flat.►Place and hold the remote control against the reader.►With a manual gearbox, place the gear lever in neutral, then fully depress the clutch pedal.►With an automatic gearbox, select modeP, then depress the brake pedal.►Press the "START/STOP" button.The engine starts.Back-up switch-offIf the electronic key is not detected or is no longer in the recognition zone, a message appears in the instrument panel when closing a door or trying to switch off the engine.►To confirm the instruction to switch off the engine, press the "START/STOP" button for approximately 5seconds.In the event of a fault with the electronic key, contact a PEUGEOT dealer or a qualified workshop.Emergency switch-offIn case of emergency only, the engine can be switched off without conditions (even when driving).►Press the "START/STOP" button for about 5seconds.In this case, the steering column locks as soon as the vehicle stops.
115Driving6On certain versions with automatic gearbox (EAT6/EAT8), the steering column does not lock.Electric parking brakeIn automatic mode, this system applies the parking brake when the engine is switched off and releases it when the vehicle moves off.At any time, with the engine running:►To apply the parking brake, briefly pull the control.►To release it, briefly push the control while pressing the brake pedal.Automatic mode is activated by default.This automatic operation can be deactivated in certain situations.Indicator lampThis indicator lamp comes on both on the instrument panel and on the control to confirm that the parking brake has been applied, accompanied by display of the message "Parking brake applied".The indicator lamp goes out to confirm the release of the parking brake, accompanied by the display of the message "Parking brake released".The indicator lamp flashes in response to a manual request to apply or release the brake. In the event of a battery failure, the electric parking brake will not operate. As a safety measure, with a manual gearbox, if the parking brake is not applied, immobilise the vehicle by engaging a gear.As a safety measure, with an automatic gearbox, if the parking brake is not applied, immobilise the vehicle by placing the supplied chocks against one of the wheels.Contact a PEUGEOT dealer or a qualified workshop.Before leaving the vehicle, check that the parking brake is applied: the parking brake indicator lamps on the instrument panel and the control must be on fixed.If the parking brake is not applied, there is an audible signal and a message is displayed on opening the driver's door.Never leave a child alone inside the vehicle, as they could release the parking brake.When the vehicle is parked: on a steep slope, heavily loaded or during towingWith a manual gearbox, turn the wheels toward the pavement and engage a gear.With an automatic gearbox, turn the wheels toward the pavement and select modeP.When towing, the vehicle is approved for parking on slopes of up to 12%.Manual operationManual releaseWith the ignition on or engine running:►Press the brake pedal.►While maintaining pressure on the brake pedal, briefly push the control.If the brake pedal is not depressed, the parking brake is not released and a message is displayed.
116DrivingManual applicationWith the vehicle stationary:►Briefly pull the control.The control indicator lamp flashes to confirm the application request.Automatic operationAutomatic releaseFirst ensure that the engine is running and that the driver's door is closed.The electric parking brake gradually releases automatically as the vehicle moves off.With a manual gearbox►Fully depress the clutch pedal and engage first gear or reverse.►Depress the accelerator pedal and release the clutch pedal.With an automatic gearbox►Depress the brake pedal.►Select modeD, M orR.►Release the brake pedal and depress the accelerator pedal.If the brake does not release automatically, check that the front doors are fully closed.When stationary with the engine running, do not depress the accelerator pedal unnecessarily. Risk of parking brake release.Automatic applicationWith the vehicle stationary, the parking brake is applied automatically when the engine is switched off.It is not applied automatically if the engine stalls or enters STOP mode with Stop & Start.In automatic mode, the parking brake can be manually applied or released at any time using the control.Special casesImmobilising the vehicle with the engine runningTo immobilise the vehicle with the engine running, briefly pull the control.Parking the vehicle with the brake releasedIn very cold conditions (ice), applying the parking brake is not recommended.To immobilise the vehicle, engage a gear or place the chocks against one of the wheels.With an automatic gearbox, mode P is automatically selected when the ignition is switched off. The wheels are blocked.For more information on Free-wheeling, refer to the corresponding section.With an automatic gearbox, while mode N is selected, opening the driver’s door triggers an audible signal. It stops when the driver's door closes again.Deactivating automatic operationIn some situations, for example when it is extremely cold or when towing (e.g. caravan, breakdown), it may be necessary to deactivate automatic operation of the system.►Start the engine.►Use the control to apply the parking brake, if it is released.►Take your foot fully off the brake pedal.►Keep the control pushed in the release direction for 10 to a maximum of15 seconds.
117Driving6►Release the control.►Depress and hold the brake pedal.►Pull the control in the application direction for 2seconds.This indicator lamp on the instrument panel comes on to confirm deactivation of the automatic functions.►Release the control and the brake pedal.From this point onwards, only the manual functions, using the control, allow the parking brake to be applied and released.►Follow this procedure again to reactivate automatic operation (confirmed by the indicator lamp on the instrument panel going out).Emergency brakingIf depressing the brake pedal fails to provide effective braking or in exceptional circumstances (e.g.driver unwell, assisted driving), the vehicle can be braked by sustained pulling on the electric parking brake control. Braking continues for as long as the control is kept pulled, and ceases when the control is released.The ABS and DSC systems stabilise the vehicle during emergency braking.If emergency braking malfunctions, the message "Parking brake fault" will be displayed on the instrument panel.If the ABS and DSC systems malfunction, indicated by lighting one or both warning lamps on the instrument panel, the vehicle’s stability is no longer ensured.►In this case, ensure the vehicle's stability by successive and repeated "pull-release" actions on the electric parking brake control until the vehicle comes to a complete stop.6-speed manual gearboxEngaging 5th or 6th gear►Move the gear selector fully to the right to engage 5th or 6th gear.Failure to follow this instruction could cause permanent damage to the gearbox (inadvertent engagement of 3rd or 4th gear).Engaging reverse gear►Raise the trigger under the knob and move the gear lever to the left, then forwards.Only engage reverse gear when the vehicle is stationary with the engine at idle.As a safety precaution and to facilitate starting of the engine, always select neutral and depress the clutch pedal.Automatic gearbox (type1)With petrol/ Diesel enginesAutomatic 6-speed or 8-speed gearbox with push selector. It also offers a manual mode with gear changes via control paddles located behind the steering wheel.With rechargeable hybrid enginesAutomatic 8-speed gearbox with push selector and regenerative braking function.With the exception of the manual mode and regenerative braking function, its operation is identical to that of other EAT8 gearboxes.
118DrivingPush selectorP.Auto ParkPress this button to switch to Parking mode.For parking the vehicle: the front wheels are blocked.R.ReverseN.NeutralTo free-wheel and move the vehicle, with the ignition off.For more information on Free-wheeling, refer to the corresponding section.D.Driving in automatic modeThe gearbox manages gear changes according to the style of driving, the road profile and the vehicle load.M.Driving in manual mode (Petrol/ Diesel)Press this button to switch to manual mode.The driver changes gear using the steering-mounted controls.B.Driving in automatic mode with regenerative braking function (Rechargeable hybrid)Press this button to activate the regenerative braking function.The gearbox also manages braking when the accelerator pedal is released.►In mode N, with your foot on the brake pedal, push without passing the point of resistance:•Forwards, mode R is selected.•Backwards, mode D is selected.Release the selector fully after each push; it will then return to its initial position.Special casesTo avoid mode N (quick change from D to R and back again):►In mode R, push backwards past the point of resistance, mode D is selected.►In mode D, push forwards past the point of resistance, mode R is selected.►To return to mode N, push without passing the point of resistance.Steering-mounted controls(Depending on equipment)In modeM orD, the steering-mounted control paddles can be used to change gear manually.They cannot be used to select neutral or to engage or disengage reverse gear.►Pull the "+" or "-" paddle towards you and release to shift up or down a gear, respectively.Information displayed on the instrument panelWhen the ignition is switched on, the gearbox status is displayed on the instrument panel:PParkingRReverseNNeutralD1...6 / 8Automatic forward gearB1...8Automatic forward gear with regenerative braking function activatedM1...6 / 8Manual forward gearIn all-electric driving, the gear engaged is not indicated.The state of the gearbox remains displayed on the instrument panel for a few seconds after switching off the ignition.
119Driving6OperationOnly appropriate mode change instructions are validated.With the engine running, if it is necessary to depress the brake pedal to change modes, an alert message will be displayed on the instrument panel.With the engine running and the brakes released, if R, D or M is selected, the vehicle moves off, even without pressing the accelerator pedal.Never depress the accelerator and brake pedals at the same time - risk of damage to the gearbox!If you open the driver's door while mode N is engaged, an audible signal will sound and mode P will be engaged. The audible signal stops when the driver's door is closed.At speeds below 3 mph (5km/h), opening the driver’s door will engage mode P- risk of sudden braking!In the event of battery failure, it is essential to place the chock(s) supplied with the tool kit against one of the wheels to immobilise the vehicle.Special aspects of automatic modeThe gearbox selects the gear that provides optimal performance based on ambient temperature, road profile, vehicle loading and driving style.For maximum acceleration, press the accelerator fully down (kick-down). The gearbox changes down automatically or holds the selected gear until the maximum engine speed is reached.Steering mounted controls allow the driver to temporarily select a gear, if the vehicle speed and engine speed conditions permit.Special aspects of manual modeThe gearbox only changes from one gear to another if the vehicle speed and engine speed conditions permit.Regenerative braking (Brake function)The regenerative braking function emulates engine braking, slowing the vehicle with no need to depress the brake pedal. When the driver releases the accelerator pedal, the vehicle slows down more quickly.The energy recovered when the accelerator pedal is released is used to partially recharge the traction battery.This partial recharging has no effect on the charge level indicator.The resulting deceleration of the vehicle does not cause the brake lamps to come on.►Frommode D, press button B to activate/deactivate the function.D on the instrument panel is replaced with B.The state of the function is not saved when the ignition is switched off.In some situations (e.g.battery full, extreme temperatures), the amount of regenerative braking may be temporarily limited, resulting in less deceleration.The driver must remain alert to traffic conditions and must always be ready to use the brake pedal.Regenerative braking using the brake pedalEnergy recovery can also be produced by depressing the brake pedal in order to partially recharge the traction battery, without affecting the charge level indicator.Starting the vehicle►Fully depress the brake pedal.►Start the engine.►With your foot on the brake pedal, push once or twice backwards to select automatic mode D, or forwards to shift into reverse gear R.►Release the brake pedal.
120Driving►Accelerate gradually to automatically release the electric parking brake.The vehicle moves off immediately.Automatic gearboxNever try to start the engine by pushing the vehicle.Switching the vehicle offRegardless of the current gearbox mode, mode P is immediately engaged automatically when the ignition is switched off.However, in mode N, mode P will be engaged after a delay of 5 seconds (time to enable free-wheeling mode).Check that modeP has been engaged and that the electric parking brake was applied automatically; if not, apply it manually.The corresponding indicator lamps on the gear selector and the electric parking brake control must be on, as well as the indicatorlamps on the instrument panel.Gearbox malfunctionThis warning lamp comes on, accompanied by an audible signal and the display of a message.Go to a PEUGEOT dealer or a qualified workshop.Do not drive faster than 62mph (100km/h), keeping to the speed limit.Switching of the gearbox to back-up modeMode D locks in third gear.The paddles on the steering wheel do not work and mode M is no longer accessible.You may feel a significant jolt on engaging reverse gear. This will not damage the gearbox.Selector malfunctionMinor malfunctionThis warning lamp comes on, accompanied by the display of a message and an audible signal.Drive carefully.Go to a PEUGEOT dealer or a qualified workshop.In some cases, the selector indicator lamps may no longer come on, but the gearbox state is still displayed on the instrument panel.Major malfunctionThis warning lamp comes on, accompanied by the display of a message.You must stop the vehicle.Stop as soon as it is safe to do so and switch off the ignition.Contact a PEUGEOT dealer or a qualified workshop.Automatic gearbox (type2)With petrol/ Diesel enginesAutomatic 6-speed or 8-speed gearbox with push selector. It also offers a manual mode with gear changes via control paddles located behind the steering wheel.With rechargeable hybrid enginesAutomatic 8-speed gearbox with push selector and regenerative braking function.With the exception of the manual mode and regenerative braking function, its operation is identical to that of other EAT8 gearboxes.
121Driving6Push selectorPParkingTo park the vehicle: the front wheels are blocked.RReverse gearNNeutralTo move the vehicle with the ignition off, or to allow it to free-wheel.For more information on Changing to free-wheeling, refer to the corresponding section.DDriving in automatic mode (Petrol/ Diesel)The gearbox manages gear changes according to the style of driving, the road profile and the vehicle load.D/BDriving in automatic mode (D) or driving in automatic mode with regenerative braking (B) (Rechargeable hybrid)The gearbox manages gear changes according to the style of driving, the road profile and the vehicle load. With the regenerative braking function activated, the gearbox also controls braking when the accelerator pedal is released.MDriving in manual mode (Petrol/ Diesel)The driver changes gear using the steering-mounted controls.UnlockTo unlock the gearbox and come out ofP or to change toR, with the foot on the brake pedal.Press and hold this button before pushing the selector.►Move the selector by pressing it forwards (N or R) or rearwards (N or D) once or twice, passing the point of resistance if necessary.The push selector returns to its initial position when released.For example, to change fromP to R, while pressing Unlock, push forward twice without crossing the point of resistance or push once crossing the point of resistance:–In the first case, the gearbox goes fromP toN, then fromN toR.–In the second case, the gearbox goes directly fromP toR.Steering-mounted controls(Depending on equipment)In modeM orD, the steering-mounted control paddles can be used to change gear manually.They cannot be used to select neutral or to engage or disengage reverse gear.
122Driving►Pull the "+" or "-" paddle towards you and release to shift up or down a gear, respectively.Information displayed on the instrument panelWhen the ignition is switched on, the gearbox status is displayed on the instrument panel:PParkingRReverseNNeutralD1...6 / 8Automatic forward gearB1...8Automatic forward gear with regenerative braking function activatedM1...6 / 8Manual forward gearIn all-electric driving, the gear engaged is not indicated.The state of the gearbox remains displayed on the instrument panel for a few seconds after switching off the ignition.OperationWith the engine running, if it is necessary to press the brake pedal and/or the Unlock button in order to change mode, an alert message is displayed in the instrument panel.Only appropriate attempted changes of mode are accepted.With the engine running and the brakes released, if R, D or M is selected, the vehicle moves off, even without pressing the accelerator pedal.Never press the accelerator and brake pedals at the same time - risk of damage to the gearbox!In the event of a battery failure, you must place the chocks supplied with the vehicle tools against one of the wheels to immobilise the vehicle.Unlocking the gearbox–From mode P:►Fully depress the brake pedal.►Press the Unlock button.►While continuing to press the brake pedal and the Unlock button, select another mode.–From neutral N, at a speed below 3 mph (5km/h):►Fully depress the brake pedal.►While continuing to depress the brake pedal, select another mode.Engaging reverse gear►Slow down until you come to a stop.►Depress the brake pedal, then press the Unlock button.►While continuing to press, select modeR.Manual modeEntering the mode:►With mode D initially selected.►Press button M; the green indicator lamp in the button comes on.Exiting the mode:►Push forwards once to return to D.or►Press button M; the indicator lamp in the button goes off.Switching off the ignitionTo switch off the ignition, the vehicle must be stationary.Free-wheelingFor more information on Free-wheeling, refer to the corresponding section.If you open the driver's door while mode N is engaged, an audible signal will sound. It will stop when you close the driver's door again.Special aspects of automatic modeThe gearbox selects the gear that provides optimal performance based on ambient temperature, road profile, vehicle loading and driving style.For maximum acceleration, press the accelerator fully down (kick-down). The gearbox changes down automatically or holds the selected gear until the maximum engine speed is reached.Steering mounted controls allow the driver to temporarily select a gear, if the vehicle speed and engine speed conditions permit.
123Driving6Special aspects of manual modeThe gearbox only changes from one gear to another if the vehicle speed and engine speed conditions permit.Regenerative braking (Brake function)The regenerative braking function emulates engine braking, slowing the vehicle with no need to depress the brake pedal. When the driver releases the accelerator pedal, the vehicle slows down more quickly.The energy recovered when the accelerator pedal is released is used to partially recharge the traction battery.This partial recharging has no effect on the charge level indicator.The resulting deceleration of the vehicle does not cause the brake lamps to come on.►From mode D/B, move the push selector backwards to activate/deactivate the function.D on the instrument panel is replaced with B.The state of the function is not saved when the ignition is switched off.In some situations (e.g.battery full, extreme temperatures), the amount of regenerative braking may be temporarily limited, resulting in less deceleration.The driver must remain alert to traffic conditions and must always be ready to use the brake pedal.Regenerative braking using the brake pedalEnergy recovery can also be produced by depressing the brake pedal in order to partially recharge the traction battery, without affecting the charge level indicator.Starting the vehicleFrom mode P:►Fully depress the brake pedal.►Start the engine.►Maintaining pressure on the brake pedal, press the Unlock button.►Push once or twice rearwards to select the automatic modeD, or forwards to engage reverseR.From neutralN:►Fully depress the brake pedal.►Start the engine.►Maintaining pressure on the brake pedal, push rearwards to select the automatic modeD, or forwards, while pressing the Unlockbutton to engage reverseR.Then, fromD orR:►Release the brake pedal.►Accelerate gradually to automatically release the electric parking brake.The vehicle moves off immediately.Automatic gearboxNever try to start the engine by pushing the vehicle.Switching the vehicle offRegardless of the current gearbox mode, mode P is immediately engaged automatically when the ignition is switched off.However, in mode N, mode P will be engaged after a delay of 5 seconds (time to enable free-wheeling mode).Check that modeP has been engaged and that the electric parking brake was applied automatically; if not, apply it manually.The corresponding indicator lamps on the gear selector and the electric parking brake control must be on, as well as the indicatorlamps on the instrument panel.Gearbox malfunctionThis warning lamp comes on, accompanied by an audible signal and the display of a message.Go to a PEUGEOT dealer or a qualified workshop.Do not drive faster than 62mph (100km/h), keeping to the speed limit.
124DrivingSwitching of the gearbox to back-up modeMode D locks in third gear.The paddles on the steering wheel do not work and mode M is no longer accessible.You may feel a significant jolt on engaging reverse gear. This will not damage the gearbox.Selector malfunctionMinor malfunctionThis warning lamp comes on, accompanied by the display of a message and an audible signal.Drive carefully.Go to a PEUGEOT dealer or a qualified workshop.In some cases, the selector indicator lamps may no longer come on, but the gearbox state is still displayed on the instrument panel.Major malfunctionThis warning lamp comes on, accompanied by the display of a message.You must stop the vehicle.Stop as soon as it is safe to do so and switch off the ignition.Contact a PEUGEOT dealer or a qualified workshop.Hill start assistThis system keeps the vehicle briefly stationary (for approximately 2seconds) when making a hill start, while you transfer your foot from the brake pedal to the accelerator pedal.The system is only active when:–The vehicle is completely stationary, with your foot on the brake pedal.–Certain slope conditions are met.–The driver’s door is closed.Do not leave the vehicle while it is being held temporarily by hill start assist.If someone needs to get out of the vehicle with the engine running, apply the parking brake manually. Then check that the parking brake indicator lamp and the P indicator lamp in the electric parking brake control are on fixed.The hill start assist function cannot be deactivated. However, using the parking brake to immobilise the vehicle interrupts its operation.OperationFacing uphill, with the vehicle stationary, the vehicle is held for a short time when the driver releases the brake pedal:–If first gear or neutral is engaged on a manual gearbox.–If mode D or M is selected on an automatic gearbox.Facing downhill, with the vehicle stationary and reverse gear engaged, the vehicle is held for a short time when the driver releases the brake pedal.MalfunctionIf the event of a malfunction, these warning lamps light up on the instrument panel, accompanied by the display of a message.
125Driving6Have it checked by a PEUGEOT dealer or a qualified workshop.Driving modesThe driving modes available depend on the engine and equipment of the vehicle.Driving modes are selected using one of the following controls, depending on version:1.Pressing the control activates Eco mode. The indicator lamp comes on.2.Pressing the control activates Sport mode. The indicator lamp comes on.3.Pressing the control displays the modes on the instrument panel.When the message disappears, the selected mode is activated and remains indicated on the instrument panel (except Normalmode).With petrol/Diesel enginesWhenever the ignition is switched on, Normaldriving mode is selected by default.NormalTo restore the default settings.EcoTo reduce energy consumption by reducing the performance of the heating and air conditioning, without deactivating them.SportWith a manual gearbox: to obtain more dynamic driving with action on the power steering, accelerator and the possibility of displaying the vehicle’s dynamic settings on the instrument panel.With an automatic gearbox: to obtain more dynamic driving with action on the power steering, accelerator, gear changes and possibility of displaying the vehicle’s dynamic settings on the instrument panel.Coasting modeDepending on version or engine, with an EAT8 gearbox and the gear selector in mode D, except inSportmode, gradually and fully releasing the accelerator pedal allows free-wheeling which can save fuel.A drop in engine speed is normal (rev counter at idle, drop in engine noise).With rechargeable hybrid enginesWhenever the ignition is switched on, Electricdriving mode is selected by default.ElectricAllows driving using 100% electrical energy. The maximum speed is approximately 84 mph (135km/h).When starting the vehicle, if the conditions do not allow the activation or retention of Electricmode, the message "Electric mode currently unavailable" is displayed on the instrument panel. The vehicle automatically changes to Hybrid mode.If an LED comes on under the interior rear view mirror, visible from outside the vehicle, this confirms that you are driving in Electric mode (depending on country of sale).The LED can be deactivated by inserting the tip of a paper clip or other similar object into the hole located underneath the interior rear view mirror.Conditions of activation–Adequate battery charge level. Charging the vehicle after each drive is therefore recommended. Electric mode is available as long as there is power left in the battery.–Outside temperature between approximately -5°C and 45°C. Manually exiting the mode
126Driving►Fully depress the accelerator pedal, or►Select another mode.In case of non-use of the vehicle for a long period (several months), a restart of the petrol engine may occur even if the battery is charged.In the event of multiple starts of the internal combustion engine without a sufficient rise in temperature,Electricmodemay be temporarily unavailable (natural phenomenon of dilution of fuel in oil). The message "Electric mode unavailable: automatic operation in progress" then appears on the instrument panel.To regain normal electrical operation, drive approximately 50 miles (80 km) in "motorway" conditions or approximately 125 miles (200 km) in urban conditions.This phenomenon does not cause any mechanical or electrical damage. It can occur several times in the life of the vehicle.HybridTo optimise the vehicle's fuel consumption by managing the alternating or simultaneous operation of the two types of engine, depending on driving conditions and driving style.In Hybrid mode, it is possible to drive in 100% electric mode if the battery charge level is sufficient and acceleration requirements are moderate.SportTo obtain more dynamic driving in order to benefit from the maximum performance of the vehicle.Electric power is used to supplement the petrol engine as long as there is energy left in the battery.4WD (4-wheel drive)(Depending on version)Improves the vehicle's grip at low and moderate speeds by driving all 4 wheels continuously.4WD mode (4-wheel drive) is especially suited to driving on snow-covered roads and difficult terrain (e.g.mud, sand) as well as ford crossings, at moderate speed.Depending on the driving conditions and the battery charge level, 4WD mode may be 100% electric.If the system does not detect a situation of wheel slipping or poor grip after 300 metres of driving, it switches to Hybrid mode.This mode will be even more effective if the vehicle is fitted with suitable tyres, such as winter tyres.The grip can be improved up to 84 mph (135km/h) using the electric motors; above this speed, the vehicle is driven by the front wheels only.Gear shift indicator(Depending on engine)This system is designed to reduce fuel consumption by recommending the most suitable gear.OperationDepending on the driving situation and the vehicle's equipment, the system may recommend skipping one or more gears.Gear engagement recommendations are not to be considered mandatory. Indeed, the configuration of the road, the traffic density and safety remain determining factors when choosing the best gear. Therefore, the driver remains responsible for deciding whether or not to follow the system’s advice.The system cannot be deactivated.With an automatic gearbox, the system is only active in manual operation.The information appears on the instrument panel, in the form of an arrow and the recommended gear.The system adapts the gear change instructions according to the driving conditions (e.g.slope, load) and driving style (e.g.power demand, acceleration, braking).The system never suggests:–engaging first gear;–engaging reverse gear.
127Driving6Stop & StartThe Stop & Start function puts the engine temporarily into standby - STOP mode - during phases when the vehicle is stationary (e.g.red lights, traffic jams). The engine automatically restarts - START mode - as soon as the driver indicates the intention of moving off again.Primarily designed for urban use, the function is intended to reduce fuel consumption and exhaust emissions as well as the noise level when stationary.The function does not affect the functionalities of the vehicle, in particular the braking.Deactivation/ReactivationThe function is activated by default when the ignition is switched on.The settings are changed via the Driving/Vehicle touch screen menu.A message on the instrument panel confirms the change of status.When the function is deactivated, if the engine was in standby, it restarts immediately.Associated indicator lampsFunction activated. Function deactivated or malfunction. Opening the bonnetBefore doing anything under the bonnet, deactivate the Stop & Start system to avoid any risk of injury caused by the engine restarting automatically.Driving on flooded roadsBefore entering into a flooded area, it is strongly recommended that you deactivate the Stop & Start system.For more information on Driving recommendations, particularly on flooded roads, refer to the corresponding section.OperationMain conditions for operation–The driver’s door must be closed.–The driver's seat belt must be fastened.–The level of charge in the battery must be sufficient.–The temperature of the engine must be within its nominal operating range.–The outside temperature must be between 0°C and 35°C.Putting the engine into standby (STOP mode)The engine automatically enters standby mode as soon as the driver indicates their intention to stop:–With a manual gearbox, at speeds below 2 mph (3 km/h) on 1.5 BlueHDi versions, or with the vehicle stationary on 1.2 PureTech versions, when you place the gear lever in neutral and release the clutch pedal.–With an automatic gearbox, at speeds below 12 mph (20 km/h) on BlueHDi versions, or with the vehicle stationary on other versions, when you depress the brake pedal or place the gear selector in mode N.Time counterA time counter adds up the time spent in standby during the journey. It is reset to zero every time the ignition is switched on.Special casesThe engine will not go into standby if the conditions for operation are not met and in the following cases:–Steep slope (ascending or descending).–Vehicle has not exceeded 6 mph (10km/h) since the last engine start.–Sport mode selected (depending on equipment).–Electric parking brake applied or being applied.–Needed to maintain a comfortable temperature in the passenger compartment.–Demisting active.In these cases, this indicator lamp flashes for a few seconds, then goes off.
128DrivingAfter the engine has restarted, STOP mode is not available until the vehicle has reached a speed of 5 mph (8km/h).During parking manoeuvres, STOP mode is not available for a few seconds after coming out of reverse gear or turning the steering wheel.Restarting the engine (START mode)The engine automatically restarts as soon as the driver indicates the intention of moving off again:With a manual gearbox: with the clutch pedal fully depressed.With an automatic gearbox:–With the selector in mode D or M: with the brake pedal released.–With the selector in mode N and the brake pedal released: with the selector at D or M.–With the selector in mode P and the brake pedal depressed: with the selector at R, N, Dor M.–With reverse gear engaged.Special casesThe engine will restart automatically if the conditions for operation are met again and in the following cases:–Vehicle speed exceeds 16 mph (25 km/h) with 2.0 BlueHDi versions with automatic gearbox in mode D, or 2 mph (3 km/h) with other versions.–The electric parking brake is being applied.–Deselecting the Sport mode (depending on equipment).In these cases, this indicator lamp flashes for a few seconds, then goes off.MalfunctionsIn the event of a fault with the system, this warning lamp flashes for a few moments on the instrument panel, then remains on, accompanied by the display of a message.Have it checked by a PEUGEOT dealer or a qualified workshop.The vehicle stalls in STOP modeAll of the instrument panel warning lamps come on if there is a fault.►Switch off the ignition then start the engine again with the key or the "START/STOP" button.12V batteryThe Stop & Start system requires a 12 V battery of specific technology and specification.All work must be carried out only by a PEUGEOT dealer or a qualified workshopTyre under-inflation detectionThis system alerts the driver if one or more tyres suffer a drop in pressure.The alert is raised when the vehicle is moving, not when stationary.It compares the information given by the wheel speed sensors with reference values, which must be reinitialised every time the tyre pressures are adjusted or a wheel changed.It takes into account the last values stored during the reinitialisation request. It is therefore essential that the tyre pressure is correct during the operation. This operation is the driver’s responsibility.The tyre under-inflation detection cannot, in any circumstances, replace the need for vigilance on the part of the driver.This system does not avoid the need to regularly check the tyre pressures (including the spare wheel), especially before a long journey.Driving with under-inflated tyres, particularly in adverse conditions (heavy load, high speed, long journey):–worsens road-holding.–lengthens braking distances.–causes premature wear of the tyres.–increases energy consumption.The inflation pressures defined for the vehicle can be found on the tyre pressure label.For more information on the Identification markings, refer to the corresponding section.
129Driving6Checking tyre pressuresThis check should be done monthly when the tyres are "cold" (vehicle stopped for 1 hour or after a journey of less than 6 miles (10km) at moderate speeds).Otherwise, add 0.3 bar to the pressures shown on the label.Snow chainsThe system does not have to be reinitialised after fitting or removing snow chains.Under-inflation alertThis is signalled by the fixed illumination of this warning lamp, accompanied by an audible signal and, depending on equipment, the display of a message.►Reduce speed immediately, avoid excessive steering movements and avoid sudden braking.►Stop the vehicle as soon as it is safe to do so.The loss of pressure detected may not always cause visible deformation of the tyre.Do not rely on just a visual check.►Using a compressor, such as the one in the temporary puncture repair kit, check the pressures of all four tyres when cold.►If it is not possible to carry out this check immediately, drive carefully at reduced speed.►In the event of a puncture, use the temporary puncture repair kit or the spare wheel (depending on equipment).Driving too slowly may not ensure optimum monitoring.The alert is not immediately triggered in the event of a sudden loss of pressure or tyre blow-out. This is because analysis of the values read by the wheel's speed sensors can take several minutes.The alert may be delayed at speeds below 25 mph (40 km/h), or when adopting a sporty driving mode.The alert is kept active until the system is reinitialised.ReinitialisationThe system must be reinitialised after any adjustment to the pressure of one or more tyres, and after changing one or more wheels.Before reinitialising the system, make sure that the pressures of the four tyres are correct for the conditions of use of the vehicle and conform to the values written on the tyre pressure label.Check the pressures of the four tyres before performing the reinitialisation.The system does not advise if a pressure is incorrect at the time of reinitialisation.With the vehicle stationary, the system is reinitialised via theDriving/Vehicletouch screen menu.►In this menu, select the “Vehicle settings” tab.►On this page, select the "Under-inflation initialisation" function.►Select "Yes" to confirm.The reinitialisation is confirmed by the display of a message and an audible signal.MalfunctionIn the event of a malfunction, these warning lamps light up on the instrument panel.A message appears, accompanied by an audible signal.In this case, the tyre under-inflation monitoring function is no longer performed.Have it checked by a PEUGEOT dealer or a qualified workshop.Non-standard or 'space-saver' spare wheelThe use of this type of spare wheel may suspend tyre pressure monitoring.
130DrivingIn this case, the malfunction warning lamp comes on and disappears once the wheel has been replaced by one of uniform size (the same as the others), the pressure readjusted and thereinitialisationcarried out.Driving and manoeuvring aids - General recommendationsDriving and manoeuvring aids cannot, in any circumstances, replace the need for vigilance on the part of the driver.The driver must comply with the Highway Code, must remain in control of the vehicle in all circumstances and must be able to retake control of it at all times. The driver must adapt the speed to climatic conditions, traffic and the state of the road.It is the driver's responsibility to constantly monitor traffic conditions, assess the distance and relative speed of other vehicles, and anticipate their manoeuvres before using the direction indicator and changing lanes.These systems do not make it possible to exceed the laws of physics.Driving aidsYou should hold the steering wheel with both hands, always use the door and interior mirrors, always leave your feet close to the pedals and take a break every 2 hours.Manoeuvring aidsThe driver must always check the surroundings of the vehicle before and during the whole manoeuvre, in particular using the mirrors.Radar(s)The operation of the radar(s), along with any associated functions, may be affected by the accumulation of dirt (e.g.mud, ice), in poor weather conditions (e.g.heavy rain, snow), or if the bumpers are damaged.If the front bumper is to be repainted, contact a PEUGEOT dealer or a qualified workshop; certain types of paint could interfere with the operation of the radar(s).Driving aids cameraThis camera and its associated functions may be impaired or not work if the windscreen area in front of the camera is dirty, misty, frosty, covered with snow, damaged or masked by a sticker.In humid and cold weather, demist the windscreen regularly.Poor visibility (e.g.inadequate street lighting, heavy rain, thick fog, snowfall), dazzle (e.g.headlamps of an oncoming vehicle, low sun, reflections on a damp road, leaving a tunnel, alternating shade and light) can also impair detection performance.In the event of a windscreen replacement, contact a PEUGEOT dealer or a qualified workshop to recalibrate the camera; otherwise, the operation of the associated driving aids may be disrupted.Other camerasThe images from the camera(s) displayed on the touch screen or on the instrument panel may be distorted by the terrain.In the presence of areas in shade, or in conditions of bright sunlight or inadequate lighting, the image may be darkened and with lower contrast.Obstacles may appear further away than they actually are.SensorsThe operation of the sensors, as well as any associated functions, may be disrupted by noise pollution such as that emitted by noisy vehicles and machinery (e.g. lorries, pneumatic drills), by the accumulation of
131Driving6snow or dead leaves on the road or in the event of damaged bumpers and mirrors.When reverse gear is engaged, an audible signal (long beep) indicates that the sensors may be dirty.A front or rear impact to the vehicle can upset the sensors’ settings, which is not always detected by the system: distance measurements may be distorted.The sensors do not systematically detect obstacles that are too low (pavements, studs) or too thin (trees, posts, wire fences).Certain obstacles located in the sensors’ blind spots may not be detected or may no longer be detected during the manoeuvre.Certain materials (fabrics) absorb sound waves: pedestrians may not be detected.MaintenanceClean the bumpers and door mirrors and the field of vision of the cameras regularly.When washing your vehicle at high pressure, direct the spray from at least 30cm away from the radar, sensors and cameras.Mats/Pedal trimsThe use of mats or pedal trims not approved by PEUGEOT may interfere with the operation of the speed limiter or cruise control.To avoid any risk of jamming the pedals:–Ensure that the mat is secured correctly.–Never fit one mat on top of another.Units of speedEnsure that the units of speed displayed on the instrument panel (mph or km/h) are those for the country you are driving in.If this is not the case, when the vehicle is stationary, set the display to the required units of speed so that it complies with what is authorised locally.In case of doubt, contact a PEUGEOT dealer or a qualified workshop.Memorising speedsThis function, used only for the speed limiter and programmable cruise control, lets you save speed settings that will subsequently be proposed for the purpose of configuring these two systems.You can memorise multiple speed settings for each of the two systems.By default, some speed settings are already memorised.As a safety measure, the driver must only change speed settings when stationary.Changing a speed settingSpeed settings can be activated, deactivated, selected and changed in the Driving/ Vehicle touch screen menu."MEM" buttonWith this button, you can select a memorised speed setting to use with the speed limiter or the programmable cruise control.For more information on the Speed limiteror Cruise control, refer to the corresponding section.Road signs recognitionFor more information, refer to the General recommendations on the use of driving and manoeuvring aids.
132DrivingThis system displays the maximum speed authorised locally on the instrument panel, using:–Speed limit signs detected by the camera.–Speed limit information from the navigation system’s mapping.–Signs indicating a shared traffic zone detected by the camera.Sign detectedSuggested speed (calculated)Entry into a shared traffic zoneExample:Without PEUGEOT Connect Nav10 mph or 20km/h (depending on the units on the instrument panel)With PEUGEOT Connect NavDisplay of the speed in force in the country you are driving in.–Some supplementary traffic signs detected by the camera.Supplementary traffic sign detectedDisplay of thespeed associated with the supplementary traffic signSpeed limit when rainingExamples:If the wiper control stalk is in the "intermittent wipe" or "automatic wipe" position (in order to activate the rain sensor):68 mph (110km/h) (for example)Speed limit when towingIf an approved towing device is fixed to the vehicle:56 mph (90km/h) (for example)Speed limit applicable over a certain distanceExample:43 mph (70km/h) (for example)Supplementary traffic sign detectedDisplay of thespeed associated with the supplementary traffic signSpeed limit for vehicles with a gross vehicle weight or gross train weight less than 3.5 tonnes56 mph (90km/h) (for example)Speed limit in case of snowExample:If the outside temperature is below 3°C:19 mph (30km/h) (for example)with a "snowflake" symbolSpeed limit at certain times of the dayExample:19 mph (30km/h) (for example)with a "clock" symbolNavigation mapping should be regularly updated in order to receive accurate speed limit information from the system.
133Driving6The units for the speed limit (mph or km/h) depend on the country you are driving in.This should be taken into account to ensure you observe the speed limit.For the system to work properly when changing countries, the speed unit of the instrument panel must match that of the country you are driving in.Automatic sign reading is a driving aid system and does not always display the correct speed limits.The speed limit signs present on the road always take priority over those displayed by the system. The system is designed to detect signs that conform to the Vienna Convention on road signs.Specific speed limits, such as those for heavy goods vehicles, are not displayed.The display of the speed limit on the instrument panel is updated when passing a speed limit sign intended for cars (light vehicles).Activation/DeactivationBy default, the system is automatically activated at every engine start.The settings are changed via the Driving/Vehicle touch screen menu.Information displayed on the instrument panel1.Detected speed limit indicationor2.End of speed limit indicationThe system is active but is not detecting speed limit information.On detecting speed limit information, the system displays the value.For a suggested maximum speed, the first time that the vehicle exceeds itby more than 3 mph (5km/h) (e.g. 59 mph (95km/h)), the speed is displayed and flashes for 10 seconds (depending on version).Operating limitsThe system does not take account of reduced speed limits, especially those imposed in the following cases:–Poor weather (rain, snow).–Atmospheric pollution.–Towing.–Driving with a space-saver type spare wheel or snow chains fitted.–Tyre repaired using the temporary puncture repair kit.–Young drivers.The system may not display the speed limit if it does not detect a speed limit sign within a preset period and in the following situations:–Road signs that are obstructed, non-standard, damaged or bent.–Obsolete or incorrect maps.
134DrivingRecommendationIn addition to Road signs recognition, the driver can select the speed displayed as a speed setting for the speed limiter or cruise control using the speed limiter or cruise control 'store' button.For more information on the Speed limiter, Cruise control or Adaptive cruise control, refer to the corresponding sections.Steering-mounted controls1.Speed limiter/cruise control mode selection2.Memorise the speed settingInformation displayed on the instrument panel3.Speed limit indication4.Speed memorisation prompt5.Current speed settingStoring the speed setting►Switch on the speed limiter/cruise control.The speed limiter/cruise control information is displayed. Upon detecting a sign suggesting a new speed setting, the system displays the value and "MEM" flashes for a few seconds, prompting you to save it as a new speed setting.If there is a difference of less than 6 mph (9km/h) between the speed setting and the speed displayed by the Road signs recognition, the "MEM" symbol is not displayed.Depending on the road conditions, several speeds may be displayed.►Press button2once to save the suggested speed value.A message is displayed, confirming the request.►Press button2again to confirm and save the new speed setting.The display then reverts to its previous state.
135Driving6Extended Traffic Sign RecognitionFor more information, refer to the General recommendations on the use of driving and manoeuvring aids.This additional system recognises these road signs and displays them on the instrument panel.As you approach it, the symbol of the corresponding sign is displayed on the instrument panel.The actual road signs always take priority over those displayed by the system.The signs must comply with the Vienna Convention on road signs.Activation/DeactivationThe settings are changed via theDriving/Vehicletouch screen menu.Speed limiterFor more information, refer to the General recommendations on the use of driving and manoeuvring aids.This system prevents the vehicle from exceeding the speed programmed by the driver (speed setting).The speed limiter is switched on manually.The minimum speed setting is 19 mph (30km/h).The speed setting remains in the system memory when the ignition is switched off.Steering-mounted control1.ON (LIMIT position)/OFF2.Reduce the speed setting3.Increase the speed setting4.Pause/resume speed limiter with the speed setting previously stored5.Depending on version:Display the speed thresholds saved using the Memorising speeds functionorUse the speed suggested by the Road signs recognition (MEM display)For more information on Memorising speedsor the Road signs recognition, refer to the corresponding sections.Information displayed on the instrument panel6.Speed limiter on/pause status indication7.Speed limiter mode selection indication8.Speed setting value9.Speed suggested by the Road signs recognition function (depending on version)
136DrivingSwitching on/Pausing►Turn thumbwheel1 to the "LIMIT" position to select speed limiter mode; the function is paused.►If the limit speed setting is suitable (most recent speed setting programmed in the system), press button4to switch the speed limiter on.►Pressing button 4again temporarily pauses the function.When the speed setting remains below the vehicle's speed for a prolonged period of time, an audible warning is emitted.Adjusting the limit speed settingYou do not have to switch the speed limiter on in order to set the speed.To modify the limit speed setting based on the vehicle’s current speed:►Briefly press button2 or 3 to change the value in steps of +or -1mph (1.6 km/h).►Press and hold button2 or 3 to change the value in steps of +or -5mph (8 km/h).To change the limit speed setting using memorised speeds, via the touch screen:►Press button5 to display the memorised speed settings.►Press the touch screen button for the desired speed setting.The selection screen closes after a few moments.This setting becomes the new limit speed.To modify the cruise speed setting based on the speed suggested by the Road signs recognition, as shown on the instrument panel:►Press button5 once; a message is displayed to confirm the memorisation request.►Press button5 again to save the suggested speed.The speed is immediately shown on the instrument panel as the new speed setting.Temporarily exceeding the speed setting►Fully depress the accelerator pedal.The speed limiter is temporarily deactivated and the displayed speed setting flashes.►Release the accelerator pedal to return to below the speed setting.When exceeding the speed is not due to the driver's action (e.g.in case of a steep slope), an audible signal is triggered immediately.On a steep descent or in the event of sharp acceleration, the speed limiter will not be able to prevent the vehicle from exceeding the speed setting.If necessary, apply the brakes to control your vehicle’s speed.When the vehicle speed returns to the speed setting level, the speed limiter operates again: the speed setting display becomes fixed again.Switching off►Turn the thumbwheel1 to the "OFF" position: speed limiter information is no longer displayed.MalfunctionIn the event of a malfunction, dashes are displayed flashing and then fixed instead of the speed setting.
137Driving6Have it checked by a PEUGEOT dealer or a qualified workshop.Cruise control - Specific recommendationsThe cruise control function does not guarantee compliance with the maximum authorised speed and the safety distance between vehicles, the driver remains responsible for their driving.In the interest of public safety, only use cruise control if the traffic conditions enable vehicles to drive at a steady speed and maintain an adequate safety distance.Remain vigilant while cruise control is activated. If you press and hold one of the speed setting modification buttons, your vehicle may change speed very abruptly.When descending a steep hill, the cruise control system cannot prevent the vehicle from exceeding the set speed. Brake if necessary to control the vehicle speed.On steep climbs or when towing, the set speed may not be reached or maintained.Exceeding the programmed speed settingYou can temporarily exceed the speed setting by pressing the accelerator pedal (the programmed speed flashes).To return to the speed setting, release the accelerator pedal (when the set speed is reached again, the displayed speed stops flashing).Operating limitsNever use the system in the following situations:–In an urban area with the risk of pedestrians crossing the road.–In heavy traffic (except versions with the Stop & Go function).–On winding or steep roads.–On slippery or flooded roads.–In poor weather conditions.–In the event of restricted visibility for the driver.–Driving on a speed circuit.–Driving on a rolling road.–When using a ‘space-saver’ type spare wheel.–When using snow chains, non-slip covers or studded tyres.Cruise controlFor more information, refer to the General recommendations on the use of driving and manoeuvring aids and the Cruise control - particular recommendations.This system automatically maintains the vehicle’s speed at the value programmed by the driver (speed setting), without the use of the accelerator pedal.Cruise control is switched on manually.It requires a minimum vehicle speed of 25 mph (40km/h).With a manual gearbox, third gear or higher must be engaged.With an automatic gearbox, modeD or second gear or higher in modeM must be engaged.Cruise control remains active after changing gear on engines fitted with a manual gearbox and Stop & Start.Switching off the ignition cancels any speed setting.Steering-mounted control1.ON (CRUISE position)/OFF
138Driving2.Activate cruise control at the current speed/decrease speed setting3.Activate cruise control at the current speed/increase speed setting4.Pause/resume cruise control with the speed setting previously saved5.Depending on version:Display the speed thresholds saved using the Memorising speeds functionorUse the speed suggested by the Road signs recognition (MEM display)For more information on Memorising speedsor the Road signs recognition, refer to the corresponding sections.Information displayed on the instrument panel6.Cruise control pause/resume7.Cruise control mode selection8.Speed setting value9.Speed suggested by the Speed Limit recognition and recommendation system (depending on version)Switching on/pausing►Turn thumbwheel1 to the "CRUISE" position to select cruise control mode; the function is paused.►Press button2 or3 to activate cruise control and save a speed setting when the vehicle has reached the desired speed; the vehicle’s current speed is saved as the speed setting.►Release the accelerator pedal.►Pressing button 4 temporarily pauses the function.►Pressing button 4 again restores operation of the cruise control (ON).Cruise control can also be paused temporarily:–by pressing the brake pedal.–automatically, if the electronic stability control (ESC) system is triggered.Modifying the cruise speed settingCruise control must be active.To modify the cruise speed setting, based on the current speed of the vehicle:►Briefly press button2 or 3 to change the value in steps of +or -1mph (km/h).►Press and hold button2 or 3 to change the value in steps of +or -5mph (km/h).Pressing and holding button2 or 3results in a rapid change in the speed of the vehicle.As a precaution, we recommend setting a cruise speed fairly close to the current speed of your vehicle, to avoid any sudden acceleration or deceleration of the vehicle.To change the cruise speed setting using memorised speed settings and from the touch screen:►Press button5 to display the memorised speed settings.►Press the touch screen button for the desired speed setting.
139Driving6The selection screen closes after a few moments.This setting becomes the new cruise speed.To modify the cruise speed setting using the speed suggested by the Road signs recognition shown on the instrument panel:►Press button5 once; a message is displayed to confirm the memorisation request.►Press button5 again to save the suggested speed.The speed is immediately shown on the instrument panel as the new speed setting.Switching off►Turn the thumbwheel1 to the "OFF" position: the cruise control information disappears from the screen.MalfunctionDashes are displayed (flashing, initially, then fixed) in the event of a cruise control system malfunction.Have the system checked by a PEUGEOT dealer or a qualified workshop.Drive Assist PlusOnly available on versions with EAT8 automatic gearbox.This system automatically adjusts the speed and corrects the trajectory of the vehicle, using Adaptive cruise control with Stop&Go function in conjunction with Lane Positioning Assist.These two functions must be activated and in operation.For more information on Adaptive cruise control and Lane Positioning Assist, refer to the corresponding sections.The system assists the driver by acting on the steering, acceleration and braking within the physical limitsand capacities of the vehicle. Certain road infrastructure elements or vehicles in the surroundings may not be properly seen or may be poorly interpreted by the camera and radar, resulting in an unexpected change in direction, a lack of steering correction and/or inappropriate management of acceleration or braking.Primarily designed for driving on main roads and motorways, this system only works with moving vehicles driving in the same direction as your vehicle.Adaptive cruise controlFor more information, refer to the General recommendations on the use of driving and manoeuvring aids and the Cruise control - Specific recommendations.This system automatically maintains the vehicle speed at a value set by the driver (speed setting), while respecting a safety distance from the vehicle in front (target vehicle) previously set by the driver. The system automatically manages the acceleration and deceleration of the vehicle.With a manual gearbox, the system slows the vehicle down as far as a speed of 19 mph (30 km/h).With the Stop function (with the EAT6 automatic gearbox), the system manages braking until the vehicle comes to a complete stop.With the Stop & Go function (with the EAT8 automatic gearbox), the system manages braking until the vehicle comes to a complete stop and restarts the vehicle.The brake lamps come on if the vehicle is slowed down by the system.It can be dangerous to drive if the brake lamps are not in perfect working order.To do this, the system uses a camera fitted at the top of the windscreen and, depending on version, a radar fitted in the front bumper.
140DrivingPrimarily designed for driving on main roads and motorways, this system only works with moving vehicles driving in the same direction as your vehicle.If the driver activates the direction indicator to overtake a slower vehicle, cruise control may temporarily reduce the distance to the target vehicle to facilitate overtaking, without exceeding the speed setting.Steering-mounted controls1.ON (CRUISE position)/OFF2.Activation of cruise control at the current speed/decrease speed setting3.Activation of cruise control at the current speed/increase speed setting4.Pause/resume cruise control with the speed setting previously savedConfirmation of vehicle restart after automatic stop (versions with Stop & Go function)5.Depending on version:Display the speed thresholds saved using the Memorising speeds functionorUse the speed suggested by the Road signs recognition (MEM display)6.Display and adjustment of the distance setting to the vehicle in frontUseActivating the system (pause)►With the engine running, turn the thumbwheel 1 downwards to the CRUISE position. Cruise control is ready to operate (grey display).Switching on cruise control and setting the speedWith a manual gearbox, your speed must be between 19 and 112mph (30 and 180km/h).With an automatic EAT6 gearbox, your speed must be between 1 and 112mph (2and 180km/h).With an automatic EAT8 gearbox, your speed must be between 0 and 112mph (0and 180km/h).►Press button 2 or 3: the current speed becomes the speed setting (minimum 19 mph (30km/h)) and cruise control is immediately activated (green display).►Press 3 to increase or 2 to decrease the speed setting (steps of 5mph (km/h) if held pressed).Pressing and holding button 2 or 3results in a rapid change in the speed of the vehicle.Pausing/resumption of cruise control►Press 4 or depress the brake pedal. To pause cruise control, it is also possible to:•shift from mode D to N;•depress the clutch pedal for more than 10 seconds;•press the electric parking brake control.►Press 4 to restart cruise control. Cruise control may have been paused automatically:•when the speed of the vehicle goes below 19 mph (30km/h) with a manual gearbox.•when the speed of the engine goes below 1100 rpm with a manual gearbox.•by triggering of the ESC system.With a manual gearbox, the driver should depress the accelerator pedal to move off, then, when above 19 mph (30km/h), reactivate the system by pressing one of the buttons 2, 3 or 4.With an EAT6 gearbox, following braking that has brought the vehicle to a complete stop, the system holds the vehicle stationary; cruise control is paused. The driver should depress the accelerator pedal to move off, then, when above 1 mph (2km/h), reactivate the system by pressing one of the buttons 2, 3 or 4.With an EAT8 gearbox, following braking that has brought the vehicle to a complete stop, if the traffic conditions do not allow the vehicle to begin moving again within 3seconds of stopping,
141Driving6press button 4 or the accelerator pedal to move off.If the driver takes no action after the vehicle has been stopped, the electric parking brake is applied automatically after about 5 minutes.Cruise control remains active after changing gear, regardless of the gearbox type.When the driver attempts to reactivate cruise control, after the function has been paused, the message "Activation not possible, unsuitable conditions" is briefly displayed if reactivation is not possible (safety conditions not met).Changing the programmed speed setting with the Road signs recognition function►Press 5 to accept the speed suggested by the function on the instrument panel, then press again to confirm.To prevent sudden acceleration or deceleration of the vehicle, select a speed setting relatively close to the vehicle's current speed.Changing the inter-vehicle distance►Press 6 to display the distance setting thresholds ("Distant", "Normal" or "Close"), then press again to select a threshold.After a few seconds, the option is accepted and will be memorised when the ignition is switched off.Temporarily exceeding the speed setting►Press the accelerator pedal fully. Distance monitoring and cruise control are deactivated while acceleration is maintained. "Cruise control suspended" is displayed.Deactivating the system►Turn the thumbwheel 1 upwards to the OFFposition.Information displayed on the instrument panelThe following information can be seen on the instrument panel in "DRIVING" display mode.7.Vehicle detected by the system (full symbol)8.Cruise control active (colour not grey)9.Speed setting value10.Speed suggested by the Road signs recognition11.Vehicle held stationary (versions with automatic gearbox)12.Inter-vehicle distance setting13.Position of the vehicle detected by the systemMessages and alertsTo display the following information on the instrument panel, select the "Driving" display mode.The actual order in which these messages or alerts are displayed may vary."Cruise paused" or "Cruise control on hold" following brief acceleration by the driver."Active cruise control", no vehicle detected."Cruise paused", vehicle detected. "Active cruise control", vehicle detected. (orange)"Take back control".►Brake or accelerate, depending on the context.
142Driving(red)"Take back control".►Take back control of the vehicle immediately: the system cannot manage the current driving situation."Activation refused, conditions unsuitable".The system refuses to activate cruise control, as the necessary conditions are not fulfilled.Stop function"Cruise paused" (for a few seconds).The system has brought the vehicle to a complete stop and is keeping it immobilised: cruise control is paused.The driver must accelerate to move off again, then reactivate cruise control.Stop & Go function"To pick up again: accelerate or press the II button".The system has brought the vehicle to a complete stop.Within 3 seconds, the vehicle gradually and automatically begins moving again.Beyond 3 seconds, the driver must accelerate or press 4-II to move off again.While the vehicle is immobilised, the following recommendations apply:–The driver should not leave the vehicle.–Do not open the boot.–Do not drop off or pick up passengers.–Do not engage reverse gear.When moving off again, watch out for cyclists, pedestrians and animals, as they may not be detected properly.Operating limitsCruise control operates by day and night, in dry weather or moderate rainfall.Certain situations cannot be managed by the system and require driver intervention.Cases not taken into account by the system:–Pedestrians, cyclists, animals.–Stationary vehicles (e.g.traffic jams, breakdown).–Vehicles crossing your lane.–Vehicles driving in the opposite direction.Situations where the driver must suspend the system:–Vehicles in a tight bend.–When approaching a roundabout.–When following a narrow vehicle.Reactivate the system when conditions allow.Situations in which the driver is prompted to immediately resume control:–Excessively sharp deceleration by the vehicle in front of you.–When a vehicle cuts in sharply between your vehicle and the one in front.Some vehicles on the road may be poorly perceived or interpreted by the camera and/or the radar (e.g.truck), which
143Driving6can lead to an incorrect evaluation of distances and result in inappropriate acceleration or braking of the vehicle.Pay particular attention:–When motorcycles are present and when there are vehicles staggered across the traffic lane.–When entering a tunnel or crossing a bridge.If any of the following malfunctions occurs, do not use the system:–Following an impact on the windscreen close to the camera or on the front bumper (versions with radar).–Brake lamps not working.If the vehicle has undergone any of the following modifications, do not use the system:–Carrying long objects on roof bars.–Towing.–Use of the "space-saver" type spare wheel (depending on version).–Front end of the vehicle modified (for example by adding long-range headlamps or painting the front bumper).–Obstructed radar.MalfunctionIn the event of a malfunction, dashes are displayed instead of the speed setting.This warning lamp comes on, accompanied by a message and an audible signal, to confirm the malfunction.Have it checked by a PEUGEOT dealer or a qualified workshop.Lane positioning assistFor more information, refer to the General recommendations on the use of driving and manoeuvring aids.The system identifies the edges of the traffic lane and steers the vehicle to keep it inside this lane and maintain the lateral position chosen by the driver.To do this, the system uses a camera placed on the upper part of the windscreen.This system is particularly suited to driving on motorways and main roads.Operating conditions–Adaptive cruise control active.–Traffic lane marked out by lines on both sides.–ESC system operational.–ASR/CDS systems activated.–No trailer detected.–No 'space-saver' spare wheel in use.–Vehicle not subject to strong lateral g-forces.–Direction indicators not activated.Activation/Deactivation►With the Adaptive cruise control with Stop & Go function activated, press this button.The action is confirmed by:–The indicator lamp in the button lighting up green.–The following symbol being displayed on the instrument panel.The colour of the symbol on the instrument panel depends on the operating status of the system:(grey colour)One or more operating conditions is not met; the system is paused.(green colour)
144DrivingAll operating conditions are met; the system is active.(orange colour)System malfunction.If the driver no longer wishes to use the system for a while, they can deactivate it by pressing the button again.The indicator lamp in the button goes off and the symbol disappears from the instrument panel.The system status is saved when the ignition is switched off.Cruise controlThe driver must hold the steering wheel properly.When cruise control is activated, the symbol is displayed in green: by small steering actions, the system directs the vehicle and keeps it in the position chosen by the driver, in the traffic lane. This position is not necessarily the centre of the lane.The driver can feel movements in the steering wheel.The driver can change the position of the vehicle at any time, by turning the steering wheel, which suspends the function. The driver positions the vehicle where they wish to in the lane. When the driver feels that the vehicle’s position is appropriate, they maintain it until the function is reactivated. The system regains control by regulating on the new defined position. Pausing/Suspending the systemThe driver must act promptly if they believe that the traffic conditions or the state of the road surface require their intervention, by moving the steering wheel to temporarily suspend system operation. Any intervention on the brake pedal that causes the Adaptive cruise control to pause will also cause the system to pause.If the system detects that the driver is not holding the wheel firmly enough, it triggers a series of gradual alerts and then deactivates itself if there is no response from the driver.If the function is suspended due to the prolonged release of the force holding the steering wheel, the function must be reactivated by pressing the button again.Automatic pause–Triggering of the ESC.–Prolonged failure to detect one of the lane limit markings. In this case, the Lane keeping assist function can take over, and the system will reactivate itself once the operating conditions are met again.In response to action by the driver: suspension–Activation of the direction indicators.–Travelling outside the lane limits.–Too tight a grip on the steering wheel or dynamic action on the steering wheel.–Action on the brake pedal (resulting in a pause until cruise control is reactivated) or accelerator pedal (suspension for as long as the pedal is depressed).–Pausing of Adaptive cruise control.–Deactivation of the DSC/ASR systems.
145Driving6Driving situations and related alertsThe tables below describe the displays associated with the main driving situations.The actual order of display of these alerts may be different.Button indicator lampCruise control thumbwheelSymbolsDisplayCommentsOffCRUISE(grey)(grey)Cruise paused.Lane positioning assist not activated.OffCRUISE(green)(grey)Active cruise control.Lane positioning assist not activated.GreenCRUISE(green)(green)Drive Assist Plus activated.The system is operating normally (correction is made at the steering wheel).GreenCRUISE70(grey)(grey)Drive Assist Plus paused.GreenCRUISE(green)/(grey)(grey)Drive Assist Plus activated.All the operating conditions for lane positioning assist have not been met.GreenOFF or LIMIT(grey)(grey)Cruise control deactivated.All the operating conditions for lane positioning assist have not been met.
146DrivingButton indicator lampCruise control thumbwheelSymbolsDisplayCommentsGreenCRUISE(green)/(grey)(grey)Drive Assist Plussuspended.Cruise control and lane positioningassist are suspended.MessagesDriving situations"Activate cruise control to use lane positioning assist"Activation of lane positioningassist while cruise control is not active."Conditions unsuitable - Awaiting activation"Activation of lane positioningassist while not all conditions are met."Keep your hands on the steering wheel"Prolonged driving without holding the steering wheel, holding it improperly or without applying any force."Hold the steering wheel"Actual or imminent loss of lane positioningassist."Take back control"Simultaneous loss of cruise control and lane positioningassist.Operating limitsThe system may issue an alert when the vehicle is travelling on a long, straight road with smooth road surface even if the driver thinks they are holding the steering wheel correctly.The system may not operate or may produce unsuitable corrections to the steering in the following situations:–Poor visibility (insufficient road lighting, snowfall, rain, fog).–Dazzle (headlamps of an oncoming vehicle, low sun, reflections on a wet road surface, leaving a tunnel, alternating light and shade).–Windscreen area in front of the camera dirty, misted up, frost-covered, snow-covered, damaged or covered by a sticker.–Lane markings eroded, partially hidden (snow, mud) or multiple (roadworks, surface joints).–Travelling in a tight bend.–Winding roads.–Presence of a tarmac joint on the road.Risk of undesirable operationThe system should be deactivated in the following situations:–Driving with a "space-saver" type spare wheel.–When towing or with a bicycle carrier attached to a towing device, particularly when a trailer is not connected or the trailer is not an approved type.–Adverse weather conditions.–Driving on slippery road surfaces (risk of aquaplaning, snow, ice).–In roadworks or toll booth areas.–Driving on racing circuits.
147Driving6–Driving on a rolling road.MalfunctionIn the event of a malfunction, the Service warning lamp comes on and this (orange) symbol appears on the instrument panel, accompanied by the display of a message and an audible signal.Have it checked by a PEUGEOT dealer or a qualified workshop.Lane keeping assistFor more information, refer to the General recommendations on the use of driving and manoeuvring aids.The system corrects the vehicle's trajectory by alerting the driver as soon as it detects a risk of involuntary lane departure or crossing of a verge or hard shoulder (depending on version).To do this, the system uses a camera, placed on the upper part of the windscreen, identifying the lane markings on the ground and the side of the road (depending on version).This system is particularly useful on motorways and main roads.Operating conditions–Vehicle speed between 43 and 112 mph (70 and 180km/h).–Road marked with a central dividing line.–Steering wheel held with both hands.–Direction indicators off upon activation of the system.–ESC system activated and operational.The system helps the driver only if there is a risk of the vehicle unintentionally wandering from the lane it is being driven in. It does not manage the safe driving distance, vehicle speed or braking.The driver must hold the steering wheel with both hands so that they can maintain control whenthe conditions no longer allow the system to intervene (e.g.in the event that the central dividing line marking on the road surface disappears).OperationAs soon as the system identifies a risk of involuntarily crossing one of the lane markings detected on the ground or a lane boundary (e.g.grass verge), it performs the trajectory correction necessary to restore the vehicle to its original lane.The driver will notice a turning movement of the steering wheel.This warning lamp flashes during trajectory correction.The driver can prevent the correction by firmly holding the steering wheel (e.g.during an emergency manoeuvre).The correction is interrupted immediately if the direction indicators are operated.While the direction indicators are activated and for a few seconds after switching them off, the system considers that a change of trajectory is intentional and no correction is triggered during this period.
148DrivingDriving situations and related alertsTo receive all the necessary information on the instrument panel, first select the "Driving" display mode.The table below describes the alerts and messages displayed in different driving situations.The actual order of display of these alerts may be different.Function statusIndicator lampDisplay and/or associated messageCommentsON(grey)System active, conditions not met:–Speed below 43 mph (70km/h).–No lane marking recognised.–ASR/DSC systems deactivated or operation of ESC system triggered.–"Sporty" driving.ON(grey)Automatic standby of the function (e.g.detection of a trailer, use of the "space-saver" type spare wheel supplied with the vehicle).ON(green)Lane marking detected.Speed above 43 mph (70km/h).ON(orange)/(green)The system corrects the trajectory on the side where the risk of unintentional crossing is detected (orange line).
149Driving6Function statusIndicator lampDisplay and/or associated messageCommentsON(orange)/(green)"Put your hands back on the steering wheel"–If, during thecorrection,the system detects that the driver has not held the steering wheel for a few seconds, it stops thecorrectionand returns control to the driver.–During the trajectory correction, the system determines that the correction will not be enough: the driver is warned that they mustprovide additional trajectory correction.The duration of audible warnings will increase if multiple corrections are performed in quick succession. The warning will become continuous, persisting until the driver responds.This message may also be displayed with your hands on the steering wheel.Operating limitsThe system goes into standby automatically in the following cases:–ESC deactivated or operation triggered.–Speed below 43 mph (70km/h) or greater than 112 mph (180km/h).–Electrical connection to a trailer.–Use of a "space-saver" spare wheel detected (as detection is not immediate, deactivation of the system is recommended).–Dynamic driving style detected, pressure on the brake or accelerator pedal.–Driving over lane markings.–Activation of the direction indicators.–Crossing the inside line on a bend.–Driving on a tight bend.–Inactivity by the driver detected during correction.The following situations may interfere with the operation of the system or prevent it from working:–Insufficient contrast between the road surface and the verge or hard shoulder (e.g.shade).–Lane markings worn, hidden (e.g.snow, mud) or multiple (e.g.roadworks).–Close proximity to the vehicle in front (lane markings may not be detected).–Roads that are narrow, winding.Risk of undesirable operationThe system should be deactivated in the following situations:–When changing a wheel or working near a wheel.–Towing or with a bicycle carrier on a towing device, especially with trailer not plugged in or not approved.–Road in poor condition, unstable or with very poor grip (risk of aquaplaning, snow, ice).–Adverse weather conditions.–Driving on racing circuits.–Driving on a rolling road.
150DrivingActivation/Deactivation►Press and hold this button to deactivate or press briefly to reactivate the system at any time. Deactivation is signalled by the lighting of the indicator lamp in the button.The state of the system is stored when the ignition is switched off.MalfunctionIn the event of a malfunction, these warning lamps light up on the instrument panel, accompanied by the display of a message and an audible signal.Have it checked by a PEUGEOT dealer or a qualified workshop.Active Safety Brake with Collision Risk Alert and Intelligent emergency braking assistanceFor more information, refer to the General recommendations on the use of driving and manoeuvring aids.This system:–warns the driver that their vehicle is at risk of collision with the preceding vehicle, a pedestrian or a cyclist.–reduces the vehicle's speed to avoid a collision or to limit its severity.The speed will be reduced by a maximum of 16 mph (25km/h) (versions with camera only) or by a maximum of 31 mph (50km/h) (versions with camera and radar).The system also takes motorcyclists into account.It may also react on animals. Animals (especially animals smaller than 0.5m) and objects on the road are not necessarily detected.This system includes three functions:–Collision Risk Alert.–Intelligent emergency braking assistance (iEBA).–Active Safety Brake (automatic emergency braking).The vehicle has a camera located at the top of the windscreen and, depending on version, a radar located in the front bumper.This system does not replace the need for driver vigilance.This system is designed to assist the driver and improve road safety.It is the driver's responsibility to continuously monitor traffic conditions in accordance with applicable driving regulations.As soon as the system detects a potential collision, it prepares the braking circuit. This may cause a slight noise and a slight sensation of deceleration.
151Driving6Deactivation/ActivationBy default, the system is automatically activated at every engine start.The settings are changed via the Driving/Vehicle touch screen menu.Deactivation of the system is signalled by the illumination of this warning lamp, accompanied by the display of a message.Operating conditions and limitsVehicle moving forward without trailer.Brake system operational.DSC/ASR systems activated.Seat belts fastened for all passengers.Stabilised speed on roads with no or low curvature.This warning lamp lights up on the instrument panel without any additional message, to indicate that the automatic braking system is not available.This is a normal behavior indicating that a condition is not fulfilled and which does not request the support of a workshop.In any situations with ignition on where automatic braking presents a risk, deactivating the system via the vehicle's configuration menu is recommended, for instance:–Towing a trailer (particularly a trailer without its own braking system).–Carrying long objects on roof bars.–Driving with snow chains.–Using an automatic car wash.–Performing any maintenance (e.g.changing a wheel, working inside the engine compartment).–Placing the vehicle on a rolling bench in a workshop.–Towing the vehicle.–Following a front bumper deformation (version with radar).–Following an impact to the windscreen close to the detection camera.The system is automatically deactivated once the use of a different diameter "space-saver" type spare wheel is detected, or if a fault with the two lateral brake lamps is detected.The system diagnoses permanently its capability and may inhibit itself without specific driver indication, if the system is outside of the regular operating conditions (e.g.sensor initialization, board voltage out of regular range, activation of stability system).Therefore, the system may not be available just after starting the vehicle.It can be dangerous to drive if the brake lamps are not in perfect working order.The driver must not overload the vehicle (keep within the GVW limit and load height limits for roof bars).Following an impact (e.g. a collision), the system is automatically deactivated.Have it checked by a PEUGEOT dealer or a qualified workshop.Collision Risk AlertThis function warns the driver if there is a risk of collision with the preceding vehicle, or with a pedestrian or cyclist.Modifying the alert trigger thresholdThis trigger threshold determines the sensitivity with which the function warns of the risk of collision.The threshold is set via the Driving/Vehicle touch screen menu.►Select one of the three pre-defined thresholds: "Far", "Normal" or "Close".The last threshold selected is memorised when the ignition is switched off.OperationDepending on the collision risk detected by the system and the alert trigger threshold chosen by the driver, different levels of alert may be triggered and displayed on the instrument panel.The system takes into account the vehicle dynamics, the difference speed of the own vehicle and the object identified for the collision risk, and the operation of the vehicle (e.g.actions on the pedals, steering wheel) to trigger the alert at the most relevant moment.
152Driving(orange)Level 1: visual alert only, warning that the preceding vehicle is very close.The message "Vehicle close" is displayed.(red)Level 2: visual and audible alert, warning that a collision is imminent.The message "Brake!" is displayed.While approaching a vehicle too quickly, the level 2 alert may be displayed directly.Important: the level 1 alert depends on the trigger threshold selected. It reacts only on moving vehicles. It is disabled automatically at lower speed.It is possible that collision warnings are not given, are given too late or seem unjustified.The driver must always stay in control of the vehicle and be prepared to react at any time to avoid an accident.Intelligent emergency braking assistance (iEBA)This function increases vehicle deceleration if the driver does not brake enough to avoid a collision.This assistance is only provided if the driver presses the brake pedal.Active Safety BrakeThis function, also called "automatic emergency braking", intervenes after the acoustic alert if the driver does not operate the brake pedal quickly enough.The system aims at reducing the speed of impact or avoiding a collision if the driver fails to react.The speed will be reduced by a maximum of 16 mph (25km/h) (versions with camera only) or by a maximum of 31 mph (50km/h) (versions with camera and radar).OperationThe system operates subject to the following conditions:–At reduced speed in an urban environment, when a stationary vehicle, pedestrian or cyclist is detected.–The vehicle's speed is between 6 mph and 53 mph (10km/h and 85 km/h) (versions with camera only) or 87 mph (140 km/h) (versions with camera and radar) when a moving vehicle is detected.This warning lamp flashes (for approximately 10 seconds) as soon as the function applies the vehicle’s brakes.During the flashing time, the function is not available.With an automatic gearbox, in the event of automatic emergency braking, keep the brake pedal depressed, also after a complete stop is reached, to prevent the vehicle from rolling away.With a manual gearbox, in the event of automatic emergency braking bringing the vehicle to a complete stop, the engine may stall.The driver can override the automatic emergency braking at any time by firmly turning the steering wheel and/or firmly depressing the accelerator pedal.
153Driving6The brake pedal may feel hard and vibrate slightly while the function is operating.If the vehicle comes to a complete stop, automatic braking is maintained for 1 to 2 seconds.MalfunctionThis warning lamp lights up on the instrument panel with the message "Sensor blind" in certain cases.Version with camera only: the system is deactivated.Version with camera and radar: the system may continue to operate in a degraded mode.This may be caused by a reduced visibility (e.g.rain, fog, snow, blinding by low sun) or by a real sensor blockage. In this case, stop the vehicle and verify if the front camera or the front radar is covered by dirt, snow, ice or anything preventing the sensing.In the event of a malfunction, this warning lamp lights up on the instrument panel, accompanied by the display of a message and an audible signal.Have it checked by a PEUGEOT dealer or a qualified workshop.These warning lamps light up on the instrument panel and/or in the warning lamp display for seat belts and front passenger airbag to indicate that the driver's and/or front passenger's seat belt is not fastened (depending on version). The automatic braking system is deactivated until the seat belts are fastened.Distraction detectionFor more information, refer to the General recommendations on the use of driving and manoeuvring aids.Depending on version, the function consists of either the "Driver Attention Warning" system alone or combined with the "Driver Attention Warning by Camera" system.These systems are in no way designed to keep the driver awake or to prevent the driver from falling asleep at the wheel. It is the driver’s responsibility to stop if feeling tired.Take a break if you are feeling tired or at least every 2 hours.Activation/DeactivationThis function is set via the touch screen Driving/Vehicle menu.The state of the system is memorised when the ignition is switched off.Driver Attention WarningThe system triggers an alert when it detects that the driver has not taken a break after two hours of driving at a speed above 43 mph (70km/h).This alert is issued via the display of a message encouraging the driver to take a break, accompanied by an audible signal.If the driver does not follow this advice, the alert is repeated hourly until the vehicle is stopped.The system resets itself if one of the following conditions is met:–With the engine running, the vehicle has been stationary for more than 15 minutes.–The ignition has been switched off for a few minutes.–The driver's seat belt is unfastened and their door is opened.As soon as the speed of the vehicle drops below 43mph (70km/h), the system goes into standby.Driving time starts being counted again once the speed reaches above 43mph (70km/h).Driver Attention Warning by CameraDepending on version, the Driver Attention Warning system may be combined with the Driver Attention Warning by Camera system.
154DrivingThe system assesses the driver's level of alertness, fatigue and distraction by identifying trajectory changes in relation to the lane markings.To do this, the system uses a camera, placed on the upper part of the windscreen.This system is particularly suited to fast roads (speed higher than 43 mph (70km/h)).At a first alert level, the driver is warned by the message "Be vigilant!", accompanied by an audible signal.After three first-level alerts, the system triggers a further alert with the message "Dangerous driving: take a break", accompanied by a more pronounced audible signal.In certain driving conditions (poor road surface or strong winds), the system may give alerts independent of the driver's level of vigilance.The following situations may interfere with the operation of the system or prevent it from working:–lane markings absent, worn, hidden (snow, mud) or multiple (roadworks);–close to the vehicle ahead (lane markings not detected);–roads that are narrow, winding, etc.Blind spot monitoringFor more information, refer to the General recommendations on the use of driving and manoeuvring aids.This system warns the driver of a potential danger posed by the presence of another vehicle (car, lorry, motorcycle) in the vehicle's blind spots (areas hidden from the driver's field of vision) using sensors located on the sides of the bumpers.A warning lamp appears in the door mirror on the side in question:–fixed, immediately, when being overtaken.–flashing, after a delay of about one second, when overtaking a vehicle slowly, and when the direction indicator is used.Activation/DeactivationIt is set via the Driving/Vehicle touch screen menu.When the function is activated, this indicator lamp comes on in the instrument panel.When starting the vehicle, thewarninglamp comes on in each mirror to indicate that the system is activated.The status of the system is memorised when the ignition is switched off.The system is automatically deactivated when towing with a towing device approved by PEUGEOT.Operating conditions–All vehicles are moving in the same direction and in adjacent lanes.
155Driving6–The speed of your vehicle must be between 7 and 87 mph (12 and 140km/h).–When overtaking a vehicle, the speed difference is less than 6mph (10km/h).–When overtaken by a vehicle, the speed difference is less than 16mph (25km/h).–Traffic is flowing normally.–Overtaking a vehicle over a certain period of time and the vehicle being overtaken remains in the blind spot.–You are driving on a straight or slightly curved road.–Your vehicle is not pulling a trailer, a caravan, etc.Operating limitsNo alert is triggered in the following conditions:–presence of stationary objects (e.g.parked vehicles, safety rails, lampposts, signs).–vehicles travelling in the opposite direction.–on winding roads or in case of sharp turns.–when overtaking or being overtaken by a very long vehicle (e.g.truck, bus), which is both detected in a blind spot from behind and present in the driver's field of vision from the front.–quick overtaking manoeuvre.–very heavy traffic: vehicles detected in front and behind are confused with a lorry or a stationary object.–activation ofthePark Assistfunction. MalfunctionIn the event of a malfunction, this warning lamp flashes for a few moments in the instrument panel, accompanied by the Service warning lamp coming on and the display of a message.Have it checked by a PEUGEOT dealer or a qualified workshop.The system may be temporarily disturbed by certain climatic conditions (e.g.rain, hail).In particular, driving on a wet road or going from a dry to a wet area can cause false alerts (e.g.presence of a cloud of water droplets in the blind spot interpreted as a vehicle).In bad or wintry weather, ensure that the sensors are not covered by mud, ice or snow.Take care not to cover the warning zone in the door mirrors, or the detection zones on the front and rear bumpers with adhesive labels or other objects; they may hamper correct operation of the system.Parking sensorsFor more information, refer to the General recommendations on the use of driving and manoeuvring aids.
156DrivingThis system detects and signals the proximity of obstacles (e.g.pedestrian, vehicle, tree, barrier) using sensors located in the bumper.Rear parking sensors►Engage reverse gear to start the system (confirmed by an audible signal).The system is switched off when reverse gear is disengaged.Audible assistanceThe system signals the presence of obstacles within the sensors’ detection zone.The proximity information is given by an intermittent audible signal, the frequency of which increases as the vehicle approaches the obstacle.When the distance between the vehicle and the obstacle becomes less than about thirty centimetres, the audible signal becomes continuous.The sound emitted by the speaker (right or left) indicates the side on which the obstacle is located.Adjusting the audible signalDepending on version, with PEUGEOT Connect Radio or PEUGEOT Connect Nav, pressing this button opens the window for adjusting the volume of the audible signal.Visual assistanceThis supplements the audible signal by displaying bars on the screen that represent the distance between the obstacle and the vehicle (white: more distant, orange: close, red: very close).When the obstacle is very close, the "Danger" symbol is displayed on the screen.Front parking sensorsSupplementing the rear parking sensors, the front parking sensors are triggered when an obstacle is detected in front and the speed of the vehicle is below 6 mph (10km/h).Front parking sensor operation is suspended if the vehicle stops for more than three seconds in forward gear, if an obstacle is no longer detected or the vehicle speed exceeds 6mph (10km/h).The sound emitted by the speaker (front or rear) locates the obstacle relative to the vehicle, whether in front of or behind it on its path.Deactivation/ActivationThe settings are changed via theDriving/Vehicletouch screen menu.The system status is memorised when the ignition is switched off.The rear parking sensors system will be deactivated automatically if a trailer or bicycle carrier is connected to a towing device installed in accordance with the manufacturer's recommendations.The parking sensors are deactivated while the Park Assist function is measuring a space.For more information on the Park Assistfunction, refer to the corresponding section.Operating limitsIf the boot is heavily loaded, the vehicle may tilt, affecting distance measurements.
157Driving6MalfunctionIn the event of a malfunction when changing into reverse gear, this warning lamp lights up on the instrument panel, accompanied by the display of a message and an audible signal (short beep).Have it checked by a PEUGEOT dealer or a qualified workshop.Visiopark 1 - Visiopark 2For more information, refer to the General recommendations on the use of driving and manoeuvring aids.With the engine running, these systems allow views of your vehicle’s close surroundings to be displayed on the touch screen using one camera for Visiopark 1 and two cameras for Visiopark 2.The screen is divided into two parts with a contextual view and a view from above the vehicle in its close surroundings.The parking sensors supplement the information on the view from above the vehicle.Various contextual views may be displayed:–Standard view.–180° view.–Zoom view.AUTO mode is activated by default.In this mode, the system chooses the best viewto display(standard or zoom).You can change the type of view at any time during a manoeuvre.►Press the button in the bottom left-hand corner of the touch screen.►Select the type of view:•"Standard view".•"180° view".•"Zoom view".•"AUTO view".The display is immediately updated with the type of view selected.The system status is not saved when the ignition is switched off.Operating principleUsing one or two cameras, the close surroundings of the vehicle are recorded whilst manoeuvring at low speed.An image from above your vehicle in its close surroundings is reconstructed (represented between the brackets) in real time and as the manoeuvre progresses.It facilitates the alignment of your vehicle when parking and allows obstacles close to the vehicle to be seen. It is automatically deleted if the vehicle remains stationary for too long.With Visiopark 2, the image is created using both cameras, when going forward and when reversing.When the function is activated, it is possible that the view from above is not displayed. If
158Drivingthe system is activated when the vehicle has already moved, the view from above can be fully displayed.Visiopark 1Rear viewTo activate the camera located on the tailgate, engage reverse gear and do not exceed a speed of 6 mph (10km/h).The system is deactivated:–Automatically, at speeds above approximately 6 mph (10km/h),–Automatically, if the tailgate is opened.–Upon changing out of reverse gear (the image remains displayed for 7seconds).–By pressing the white arrow in the upper-left corner of the touch screen.AUTO modeThis mode is activated by default.Using sensors in the rear bumper, the automatic view changes from the rear view (standard) to the view from above (zoom) as an obstacle is approached at the level of the red line (less than 30cm) during a manoeuvre.Standard viewThe area behind the vehicle is displayed on the screen.The blue lines 1 represent the width of your vehicle, with the mirrors unfolded; their direction changes according to the position of the steering wheel.The red line 2 represents a distance of 30cm from the rear bumper; the two blue lines 3 and 4represent 1m and 2m, respectively.This view is available with AUTO mode or in the view selection menu.Zoom viewThe camera records the vehicle's surroundings during the manoeuvre in order to create a view from above the rear of the vehicle in its near surroundings, allowing the vehicle to be manoeuvred around nearby obstacles.This view is available with AUTO mode or in the view selection menu.Obstacles may appear further away than they actually are.It is important to monitor the sides of the vehicle during the manoeuvre, using the mirrors.Parking sensors also provide additional information about the area around the vehicle.
159Driving6180° viewThe 180° view facilitates reversing out of a parking space, making it possible to see the approach of vehicles, pedestrians and cyclists.This view is not recommended for carrying out a complete manoeuvre.It features 3 areas: left A, centre B and right C.This view is only available via the view selection menu.Visiopark 2The vehicle has a camera at the front, fitted in the grille, and a camera at the rear, located close to the tailgate opening control.Using these cameras, the system displays the vehicle's near surroundings on the touch screen, offering views from the rear of the vehicle (rear vision) when reverse gear is engaged and views from the front of the vehicle (front vision) when the gearbox is in neutral or a gear is engaged.Rear visionThe system activates automatically when reverse gear is engaged.The system is deactivated:–Automatically, at speeds above approximately 12 mph (20km/h).–When shifting out of reverse (the front vision image replaces the rear vision image for 7 seconds).–By pressing the white arrow in the upper-left corner of the touch screen.If a trailer or a bicycle carrier is fitted to the towball, the area behind the vehicle on the view from above goes dark.The surroundings are reconstructed by the front camera only.The rear vision views are similar to those for the Visiopark 1 function.For more information on the Visiopark 1function, refer to the corresponding section.Front and rear visionWith the engine running and the speed below 12 mph (20km/h), the system is activated via the Driving/Vehicle touch screen menu:►Select "Visual parking assistance".AUTO mode is displayed by default, with front vision, if the gearbox is in neutral or with a gear engaged, or with rear vision, if reverse is engaged.The system is deactivated:–Automatically above about 19 mph (30km/h) (the image disappears temporarily from 12 mph (20km/h)).–By pressing the white arrow in the upper-left corner of the touch screen.
160DrivingAUTO modeThis mode is activated by default.Using sensors in the front bumper, the automatic view changes from the front view (standard) to the view from above (zoom) as an obstacle is approached during a manoeuvre.Standard viewThe area in front of your vehicle is displayed on the screen.The orange lines 1 represent the width of your vehicle, with the mirrors unfolded; their direction changes according to the position of the steering wheel.The red line 2 represents a distance of 30 cm from the front bumper; the two orange lines 3and 4 represent 1 m and 2 m, respectively.This view is available with AUTO mode or by selecting it in the view change menu.Zoom viewThe camera records the vehicle's surroundings during the manoeuvre in order to create a view from above the front of the vehicle in its near surroundings, allowing the vehicle to be manoeuvred around obstacles nearby.This view is available with AUTO mode or in the view selection menu.Obstacles may appear further away than they actually are.It is important to check the sides of the vehicle during the manoeuvre, using the mirrors.The parking sensors also supplement the information on the vehicle's surroundings.180° viewThe 180° view assists with exiting from a parking space in forward gear, making it possible to see the approach of vehicles, pedestrians and cyclists.This view is not recommended for carrying out a complete manoeuvre.It consists of 3 areas: left A, centre B and right C.This view is available only from the view selection menu.
161Driving6Park AssistFor more information, refer to the General recommendations on the use of driving and manoeuvring aids.This system provides active parking assistance: it detects a parking space then operates the steering system to park in this space.With a manual gearbox, the driver manages the accelerator, brakes, gears and clutch.With an automatic gearbox (EAT6/EAT8), the driver manages the accelerator, brakes and gears.During phases of entry into and exit from a parking space, the system provides visual and audible information to the driver in order to make the manoeuvres safe. Several forward and reverse manoeuvres may be required.At any time, the driver can take back control by holding the steering wheel.The Park Assist system provides assistance for the following manoeuvres:A.Entry into a "parallel" parking spaceB.Exit from a "parallel" parking spaceC.Entry into a "bay" parking spaceThe Park Assist system cannot operate with the engine switched off.When Park Assist is activated, it prevents Stop & Start from going into STOP mode. In STOP mode, activation of Park Assist restarts the engine.The Park Assist system takes control of the steering for a maximum of 4 manoeuvring cycles. It is deactivated after these 4 cycles. If the vehicle is not positioned correctly, take back control to complete the manoeuvre.The sequence of manoeuvres and the driving instructions are displayed in the instrument panel.The assistance is activated: the display of this symbol and a speed limit indicate that the steering manoeuvres are controlled by the system: do not touch the steering wheel.The assistance is deactivated: the display of this symbol indicates that the steering manoeuvres are no longer controlled by the system: take over the steering.Activation of Park Assist deactivates the Blind spot monitoring.The Parking sensors function is not available during parking space measurement. It intervenes later when manoeuvring to warn that the vehicle is approaching an obstacle: the audible signal becomes continuous when the obstacle is less than 30 centimetres away.If the Parking sensors function has been deactivated, it will be automatically reactivated during the assisted manoeuvring phases.During parking and exit from parking manoeuvres, the Visiopark 1 - Visiopark 2 functions may come into operation. They allow better monitoring of the surroundings of the vehicle, by displaying additional information in the touch screen.For more information on the Visiopark 1 - Visiopark 2functions, refer to the corresponding section.In some circumstances, the sensors may not detect small obstacles located in their blind spots.Any object exceeding the size of the vehicle (e.g.roof ladder, towball) is not taken into account by the Park Assist during a manoeuvre.
162DrivingAlways check the surroundings of the vehicle before starting a manoeuvre.If the lateral distance between the vehicle and the space is too great, the system may not be able to measure the space.During manoeuvring phases, the steering wheel performs rapid turns: do not hold the steering wheel or put your hands between the spokes of the steering wheel.Beware of any object likely to block the manoeuvre (e.g.loose clothing, scarves, ties) - risk of injury!Assistance with "parallel" parking manoeuvres►When parking, select "Park Assist" in the Driving/Vehicle touch screen menu to activate the function.►Limit the vehicle speed to a maximum of 12 mph (20 km/h) and select "Enter parallel parking space" on the touch screen.To enter a "parallel" parking space, the system does not identify spaces that are clearly smaller or larger than the vehicle.►Operate the direction indicator on the side you have chosen to park in order to activate the measurement function. The vehicle must drive at a distance of between 0.5m and 1.5m from the row of parked vehicles.20►Drive at a speed below 12 mph (20 km/h) following the instructions until the system finds an available space.►Move forwards slowly until a message is displayed, accompanied by an audible signal, asking you to engage reverse gear.►Engage reverse gear, release the steering wheel and move without exceeding a speed of 4 mph (7 km/h).The assisted parking manoeuvre is in progress.7►Without exceeding 5 mph (7km/h), move forwards and backwards, aided by the warnings from the "Parking sensors" system, until the end of the manoeuvre is indicated.The end of the manoeuvre is confirmed by a message and an audible signal.Parking assistance is deactivated: you can take over the controls again.Assistance with "bay" parking manoeuvres►When parking, select “Park Assist” in the Driving/Vehicle touch screen menu to activate the function.►Limit the vehicle speed to a maximum of 12 mph (20 km/h) and select “Enter bay parking space” on the touch screen.►Operate the direction indicator on the parking side chosen to activate the measurement function. The vehicle should drive at a distance of between 0.5m and 1.5m from the row of parked vehicles.20►Drive at a speed below 12 mph (20 km/h) following the instructions until the system finds an available space.When several successive spaces are found, the vehicle will be directed towards the last one.►Move forwards slowly until a message is displayed, accompanied by an audible signal, asking you to engage reverse gear.►Engage reverse gear, release the steering wheel and move without exceeding the speed of 5 mph (7 km/h).The assisted parking manoeuvre is in progress.7►Without exceeding 5 mph (7km/h), follow the instructions and the warnings from the "Parking sensors" system, until the end of the manoeuvre is indicated.The end of the manoeuvre is confirmed by a message and an audible signal.The system is deactivated: it is possible to retake control.During a "bay" parking manoeuvre, the Park Assist system is automatically deactivated once the rear of the vehicle is within 50cm of an obstacle.
163Driving6Assistance with "parallel" parking exit manoeuvres►To leave a "parallel" parking space, switch the engine on.►With the vehicle stationary, select "Park Assist" in the Driving/Vehicletouch screen menu to activate the function.►Press "Exit parking slot" on the touch screen.►Operate the direction indicator for the exit side chosen.►Engage reverse or forward gear and release the steering wheel.The assisted parking manoeuvre is in progress.5►Without exceeding 3 mph (5km/h), move forwards and backwards, aided by the warnings from the "Parking sensors" system, until the end of the manoeuvre is indicated.The manoeuvre is complete when the vehicle's front wheels are clear of the parking space.The end of the manoeuvre is confirmed by a message and an audible signal.The system is deactivated: it is possible to retake control.DeactivationThe system is deactivated via the Driving/ Vehicle touch screen menu.The system is automatically deactivated:–when the ignition is switched off.–if the engine stalls.–if the driver's seat belt is not fastened.–on opening the driver's door.–if no manoeuvre is performed within 5 minutes of selecting the type of manoeuvre.–after a prolonged stop of the vehicle during a manoeuvre.–if the wheel anti-slip regulation (ASR) is triggered.–if the speed of the vehicle is above 43 mph (70 km/h).–when the driver interrupts the rotation of the steering wheel.–after 4 manoeuvring cycles.–if one of the front wheels encounters an obstacle.–when towing a trailer, connected electrically.Deactivation is confirmed by a message and an audible signal.The driver should then take back control of the vehicle's steering.If the system is deactivated during a manoeuvre, the driver should reactivate it to repeat the measurement.To switch the system off for a prolonged period, contact a PEUGEOT dealer or a qualified workshop.MalfunctionsIf the parking sensor malfunction occurs during use, indicated by this warning lamp coming on, it causes the function to deactivate.In the event of a malfunction, have the system checked by a PEUGEOT dealer or a qualified workshop.In the event of a power steering malfunction, this warning lamp is displayed on the instrument panel, accompanied by a warning message.You must stop as soon as it is safe to do so. Contact a PEUGEOT dealer or a qualified workshop.
Peugeot & TotalEnergies,a partnership in performance !For more than 25 years of partnership, TotalEnergies and Peugeot have pushed the limits of performance in sports competition with historic victories, in endurance races or in rallies. Today, the two brands continue their common motorsport adventure by setting out to conquer the 24h of Le Mans and the FIA World Endurance Championship in the Hybrid Hypercar category. So many challenges for which Peugeot exclusively recommends high-tech Quartz lubricants for the protection of its engines throughout their life. TotalEnergies therefore equips Peugeot vehicles with Quartz lubricants from their fi rst fi lling in the factory to the approved maintenance networks to guarantee them optimal day-to-day operation. Peugeot & TotalEnergies: offi cial partners in performance !Keep your engine younger for longer !Quartz Ineo Xtra First 0W-20 is a very high performance lubricant resulting from the joint work of the Peugeot and TotalEnergies R&D teams. Its innovative technology extends your engine’s life while reaching signifi cant fuel savings and thus limiting CO2 emissions. The product is now available in new packaging* made of 50% recycled material and 100% recyclable.* 1L & 5L produced in Europe
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131