Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot 3008 2008-2015 Practical Information Changing a wheel

PRACTICAL INFORMATION172 CHANGING A WHEEL * The tools are installed in the boot under the fl oor. To gain access to them: open the boot, place the adjustable boot fl oor at an angle (refer to the "Fittings" sec-tion), raise the fl oor, secure it by hooking its cord on the hook on the rear parcel shelf sup-port, remove the polystyrene storage box, unclip by pulling upwards then re-move the box containing the tools. Access to the tools Procedure for changing a faulty wheel for the spare wheel using the tools pro-vided with the vehicle. To make the operation easier, re-move the adjustable boot fl oor, unscrew the yellow central bolt, With the JBL bass unit remove the bass unit disconnecting the electrical harness, remove the polystyrene storage box. * Depending on destination country.
PRACTICAL INFORMATION172 CHANGING A WHEEL * The tools are installed in the boot under the fl oor. To gain access to them: open the boot, place the adjustable boot fl oor at an angle (refer to the "Fittings" sec-tion), raise the fl oor, secure it by hooking its cord on the hook on the rear parcel shelf sup-port, remove the polystyrene storage box, unclip by pulling upwards then re-move the box containing the tools. Access to the tools Procedure for changing a faulty wheel for the spare wheel using the tools pro-vided with the vehicle. To make the operation easier, re-move the adjustable boot fl oor, unscrew the yellow central bolt, With the JBL bass unit remove the bass unit disconnecting the electrical harness, remove the polystyrene storage box. * Depending on destination country.
PRACTICAL INFORMATION173 All of these tools are specifi c to your vehicle. Do not use them for other purposes. 1. Wheelbrace. For removing the wheel trim and removing the wheel bolts. 2. Jack with integral handle. For raising the vehicle. 3. "Bolt cover" tool (according to equipment). For removing the bolt protectors (covers) on alloy wheels. 4. Centring guide. For refi tting an alloy wheel to the hub. List of tools * Other accessories Wheel with trim When removing the wheel , detach the trim fi rst using the wheelbrace 1 pulling at the valve passage hole. When refi tting the wheel , refi t the trim starting by placing its notch fac-ing the valve and press around its edge with the palm of your hand. 5. Socket for the security bolts (lo-cated in the glove box). For adapting the wheelbrace to the special "security" bolts. 6. Two chocks to immobilise the vehicle. 7. Removable towing eye. Refer to "Electric parking brake" in the "Driving" section. Refer to the paragraph "Tow-ing the vehicle". 8. Electric brake emergency release control. * Depending on destination country.
PRACTICAL INFORMATION174 Access to the spare wheel * The spare wheel is installed in the boot under the fl oor. Depending on country, the spare wheel may be steel, alloy or of the "space-saver" type. To gain access to it, refer to the paragraph "Access to the tools" on the previous page. Taking out the wheel Unscrew the yellow central bolt. Raise the spare wheel towards you from the rear. Take the wheel out of the boot. Putting the wheel back in place Put the wheel back in its housing. Unscrew the yellow central bolt by a few turns then put it in place in the centre of the wheel. Tighten fully until the central bolt clicks to retain the wheel correctly. Put the box back in place in the centre of the wheel and clip it. Put the polystyrene storage box back in place. Tyre under-infl ation detection The spare wheel is not fi tted with a sensor. The punctured wheel must be repaired by a PEUGEOT dealer. * Depending on destination country.
PRACTICAL INFORMATION Parking the vehicle Immobilise the vehicle where it does not block traffi c: the ground must be level, stable and non-slippery ground. Apply the parking brake unless it has been programmed to automatic mode, switch off the ignition and en-gage fi rst gear * to lock the wheels. Check that the braking warning lamp and the P warning lamp on the park-ing brake control come on. If necessary, place a chock under the wheel diagonally opposite the wheel to be changed. The occupants must get out of the ve-hicle and wait where they are safe. Never go underneath a vehicle raised using a jack; use an axle stand. Removing a wheel List of operations Remove the chromed bolt cover from each of the bolts using the tool 3(according to equipment). Fit the security socket 5 on the wheelbrace 1 to slacken the security bolt (if your vehicle has them). Slacken the other bolts using the wheelbrace 1 only. Place the jack 2 in contact with one of the two front A or rear B locations provided on the underbody, which-ever is closest to the wheel to be changed. Extend the jack 2 until its base plate is in contact with the ground. Ensure that the centreline of the jack base plate is directly below the location Aor B used. Raise the vehicle until there is suf-fi cient space between the wheel and the ground to admit the spare (not punctured) wheel easily. Remove the bolts and store them in a clean place. Remove the wheel. * position R for the electronic gear control manual gearbox; P for the automatic gearbox.
PRACTICAL INFORMATION176 Fitting the "space-saver" spare wheel If your vehicle is fi tted with al-loy wheels, when tightening the bolts on fi tting it is normal to notice that the washers do not come into contact with the "space-saver" spare wheel. The wheel is secured by the conical contact of each bolt. Fitting a wheel List of operations Put the wheel in place on the hub using the centring guide 4 . Screw in the bolts by hand to the stop. Using the wheelbrace 1 fi tted with the security socket 5 , pre-tighten the security bolt (if your vehicle has them). Pre-tighten the other bolts using the wheelbrace 1 only. Lower the vehicle fully. Fold the jack 2 and detach it. Using the wheelbrace 1 fi tted with the security socket 5 , tighten the security bolt (if your vehicle has them). Tighten the other bolts using the wheelbrace 1 only. Refi t the chromed bolt covers on each of the bolts (according to equipment). Store the tools in the box. After changing a wheel To store the punctured wheel in the boot correctly, fi rst remove the cen-tral cover. When using the "space-saver" type spare wheel, do not exceed 50 mph (80 km/h). Have the tightening of the bolts and the pressure of the spare wheel checked by a PEUGEOT dealer with-out delay. Have the punctured wheel repaired and replace it on the vehicle as soon as possible.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131