Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot 3008 2008-2015 Practical Information 12 V battery

PRACTICAL INFORMATION12 V BATTERY Procedure for charging your battery when it is fl at or for starting the engine using another battery. Access to the battery Starting using another battery Connect the red cable to the posi-tive terminal (+) of the fl at battery A , then to the positive terminal (+) of the slave battery B . Connect one end of the green or black cable to the negative termi-nal (-) of the slave battery B . Connect the other end of the green or black cable to the earth point Con your vehicle (engine mounting). Operate the starter, let the engine run. Wait until the engine returns to idle and disconnect the cables. The battery is located under the bonnet. To gain access to it: open the bonnet using the interior release lever, then the exterior safe-ty catch, secure the bonnet stay, remove the plastic cover to gain access to the two terminals, unclip the fusebox to remove the battery, if necessary.
PRACTICAL INFORMATION190 Disconnecting the cables Raise the locking tab fully. Reconnecting the cables Position the open clip 1 of the cable on the positive terminal (+) of the battery. Press vertically on the clip 1 to posi-tion it correctly against the battery. Lock the clip by spreading the po-sitioning lug and then lowering the tab 2 . Do not force the tab as locking will not be possible if the clip is not positioned correctly; start the procedure again. Do not disconnect the terminals while the engine is running. Do not charge the batteries without disconnecting the ter-minals fi rst. Do not push the vehicle to start the engine if it is fi tted with a 6-speed electronic gear control gearbox or an automatic gearbox. The batteries contain harm-ful substances such as sul-phuric acid and lead. They must be disposed of in accordance with regulations and must not, in any circumstances, be discarded with household waste. Take used remote control batteries and vehicle batteries to a special collection point. Charging the battery using a battery charger Disconnect the battery from the vehicle. Follow the instructions for use provided by the manufacturer of the charger. Reconnect starting with the nega-tive terminal (-). Check that the terminals and connec-tors are clean. If they are covered with sulphate (whitish or greenish deposit), remove them and clean them. It is advisable to disconnect the battery if the vehicle is to be left unused for more than one month. Before disconnecting the battery Wait 2 minutes after switching off the ig-nition before disconnecting the battery. Close the windows and the doors be-fore disconnecting the battery. Following reconnection of the battery Following reconnection of the battery, switch on the ignition and wait 1 minu-te before starting to permit initialisation of the electronic systems. However, if problems remain following this opera-tion, contact a PEUGEOT dealer. Referring to the corresponding section, you must yourself reinitialise: - the remote control key, - the panoramic sunroof blind, - the satellite navigation system.
PRACTICAL INFORMATION191 Let the engine run for the duration specifi ed to ensure that the battery charge is suf-fi cient. Do not repeatedly and continuously restart the engine in order to charge the battery. A fl at battery prevents the engine from starting (refer to the "Battery" paragraph). If the telephone is being used at this time: - it will be maintained for 5 min-utes with the hands-free kit of your Peugeot Connect Sound or Peugeot Connect Navigation, - it will still be possible to fi nish the call with the Peugeot Connect Media. Exiting economy mode These functions are reactivated auto-matically next time the vehicle is driven. In order to resume the use of these functions immediately, start the en-gine and let it run: - for less than ten minutes, to use the equipment for approximately fi ve minutes, - for more than ten minutes, to use the equipment for up to approxi-mately thirty minutes. LOAD REDUCTION MODE System which manages the use of cer-tain functions according to the level of charge remaining in the battery. When the vehicle is being driven, the load reduction function temporarily de-activates certain functions, such as the air conditioning, the heated rear screen... The deactivated functions are reactivat-ed automatically as soon as conditions permit. ENERGY ECONOMY MODE System which manages the duration of use of certain functions to conserve a suffi cient level of charge in the battery. After the engine has stopped, you can still use functions such as the audio and telematics system, windscreen wipers, dipped beam headlamps, courtesy lamps, etc. for a maximum combined duration of thirty minutes. Switching to economy mode Once the thirty minutes are over, a message appears in the multifunction screen indicating that the vehicle has switched to economy mode and the ac-tive functions are put on standby.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131