Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot 208 2020-2025 Practical information Very cold climate screens

151Practical information7Only use chains that have been designed to be fitted on the type of wheel on the vehicle:Original tyre sizeMaximum link size185/65 R159 mm (PolaireXP9)195/55 R169 mm (PolaireXP9)205/45 R17Cannot be fitted with chainsFor more information on snow chains, contact a PEUGEOT dealer or a qualified workshop.Installation tips ►To fit the snow chains during a journey, stop the vehicle on a flat surface at the side of the road.►Apply the parking brake and position any wheel chocks under the wheels to prevent movement of the vehicle.►Fit the snow chains following the instructions provided by the manufacturer.►Move off gently and drive for a few moments, without exceeding 31mph (50km/h).►Stop the vehicle and check that the snow chains are correctly tightened.It is strongly recommended that you practise fitting the snow chains on a level and dry surface before setting off.Avoid driving with snow chains on roads that have been cleared of snow to avoid damaging the vehicle's tyres and the road surface. If the vehicle is fitted with alloy wheels, check that no part of the chain or its fixings is in contact with the wheel rim.Very cold climate screens(Depending on country of sale)This removable device prevents the accumulation of snow around the radiator cooling fan.It consists of two elements for the upper part of the front grille and two other elements for the lower part.In case of difficulty with installation/removalContact a PEUGEOT dealer or a qualified workshop.Before any operation, ensure that the engine is off and the cooling fan has stopped.It is essential to remove them when:–the outside temperature exceeds 10°C.–recovery is in progress.–the speed is above 75 mph (120km/h).FittingUpper/side very cold climate screensWhen fitting for the first time, adapt the 2 upper very cold climate screens to the vehicle's grille type:–Grille A, "MAINSTREAM" (MS) type.–Grille B, "UPPER" (UP) type.►For each very cold climate screen 1 and 2, cut the mounting tabs according to the type of grille A or Bthat is fitted to the vehicle.
152Practical informationIf a telephone call is in progress at the time, it will be maintained for around 10 minutes via the audio system’s hands-free system.Exiting the modeThese functions are automatically reactivated the next time the vehicle is used.To restore the use of these functions immediately, start the engine and let it run:–For less than 10 minutes, to use the equipment for approximately 5 minutes.–For more than 10 minutes, to use the equipment for approximately 30 minutes.Let the engine run for the specified duration to ensure that the battery charge is sufficient.To recharge the battery, avoid repeatedly or continuously restarting the engine.A flat battery prevents the engine from starting.For more information on the 12V battery, refer to the corresponding section.Load reduction modeThis system manages the use of certain functions according to the level of charge remaining in the battery.When the vehicle is being driven, the load reduction function temporarily deactivates certain ►Use wire cutters, taking care not to cut the tabs that are to be retained.The cuttinginstructions are printed on each inner face of the 2 upper very cold climate screens.►Place one of the upper screens against the corresponding side of the upper bumper grille.►First insert the upper mounting tabs into the bumper.►Tilt the screen downwards until the lower mounting tabs are properly seated in the bumper (press on each tab to ensure it clicks into place).►Check that the unit is held firmly in place by pressing around the edges.Repeat the same steps for the other upper screen, then for the side screen in the grille below the number plate.Lower very cold climate screen►Place the lower screen against the lower bumper grille.►Insert the mounting tabs into the bumper until they are all properly seated.►Check that the unit is held firmly in place by pressing around the edges.RemovingFor the lower and side very cold climate screen►Insert a screwdriver into the slots located on the top of the lower screen and side screen to detach them from the grille.►Gently tilt the upper screen and side screen downwards.►Pull the unit towards you and support it as it becomes unclipped.For the upper very cold climate screens►Press the lower mounting lugs to release them from the grille.►Gently tilt the upper screen upwards.►Pull the unit towards you and support it as it becomes unclipped.Energy economy modeThis system manages the duration of use of certain functions, in order to conserve a sufficient level of charge in the battery with the ignition off.After switching off the engine and for a maximum cumulative period of around 30 minutes, you can continue to use functions such as the audio and telematics system, dipped beam headlamps or courtesy lamps.Selecting the modeA confirmation message is displayed when energy economy mode is entered, and the active functions are placed on standby.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131