Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot 208 2020-2025 In the event of a breakdown Tool kit

164In the event of a breakdownWarning triangleThis reflective and dismantlabledevice is to be installed on the side of the road when a vehicle is broken down or damaged.Before getting out of the vehicleTurn on the hazard warning lamps, then put on the safety vest to assemble and install the triangle.Assembling and placing the triangleFor versions supplied with a triangle as original equipment, refer to the illustration above.For other versions, refer to the assembly instructions provided with the triangle.►Put the triangle in place behind the vehicle, as required by local legislation.Running out of fuel (Diesel)With Diesel engines, the fuel system must be primed if you run out of fuel.Before starting to prime the system, it is essential to put at least 5 litres of Diesel into the fuel tank.For more information on Refuelling and on Misfuel prevention (Diesel), refer to the corresponding section.For non-BlueHDi versions, the fuel system components are located in the engine compartment; this may be under a removable cover.For more information on the Engine compartment, in particular the location of these components under the bonnet, refer to the corresponding section.1.5 BlueHDi engines►Switch on the ignition (without starting the engine).►Wait around 1minute and switch off the ignition.►Operate the starter motor to start the engine.If the engine does not start at the first attempt, do not keep trying, but restart the procedure.1.6 HDi engines►Open the bonnet and then, if necessary, unclip the cover to access the priming pump.►Operate the priming pump repeatedly until resistance is felt (resistance may be felt at the first press).►Operate the starter motor to start the engine (if the engine does not start at the first attempt, wait around 15 seconds before trying again).►If the engine does not start after a few attempts, operate the priming pump again, then the starter motor.►Put the cover back in place and clip it in, then close the bonnet.Tool kitSet of tools supplied with the vehicle.Its content depends on your vehicle's equipment:–Temporary puncture repair kit.–Spare wheel.Access to the toolsDepending on version, the tool kit is stored in a bag or in a storage box in the boot.On the boot carpetUnder the boot carpet►Raise the boot carpet by pulling the strap to access the tools. With temporary puncture repair kit
165In the event of a breakdown8On the boot carpetUnder the boot carpet►Raise the boot carpet by pulling the strap to access the tools. With temporary puncture repair kitWith spare wheelThese tools are specific to the vehicle and may vary according to the level of equipment.Do not use them for any other purpose.The jack must only be used to change a wheel with a damaged or punctured tyre.Do not use any jack other than the one supplied with the vehicle.If the vehicle does not have its original jack, contact a PEUGEOT dealer or a qualified workshop to obtain the one that was intended by the manufacturer.The jack meets European standards, as defined in the Machinery Directive 2006/42/CE.The jack does not require any maintenance.List of tools1.Chock to immobilise the vehicle (depending on equipment)2.Socket for the wheel security bolts (located in the glove box) (depending on equipment)To adapt the wheelbrace to the special ‘security’ bolts.3.Removable towing eyeFor more information on Towing the vehicleand using the removable towing eye, refer to the corresponding section.With temporary puncture repair kit
166In the event of a breakdown4.12 V compressor with cartridge of sealant and speed limit stickerFor temporary repair of a tyre and to adjust the tyre pressure.For more information about the Temporary puncture repair kit, refer to the corresponding section.With spare wheel5.WheelbraceFor removing the wheel bolts.6.Jack with integrated handleTo raise the vehicle.7.Wheel bolt cap removal tool (depending on equipment)For removing the wheel bolt head finishers on alloy wheels.For more information on the Spare wheel, refer to the corresponding section.Temporary puncture repair kitScan the QR Code on page 3 to view explanatory videos.Made up of a compressor and a sealant cartridge,it allows you to carry out a temporary repair of the tyre so that you can drive to the nearest garage.It is designed to repair most punctures located on the tyre tread.The vehicle's electric system allows the connection of the compressor to the 12 V power supply for long enough to repair a tyre after a puncture.For more information on the Tool kit, refer to the corresponding section.Tyre inflation pressures are indicated on this label.For more information on Identification markings, particularly this label, refer to the corresponding section.Should the pressure of one or more tyres be adjusted, it is necessary to reinitialise the under-inflation detection system.For more information on Tyre under-inflation detection, refer to the corresponding section.Repair procedureDo not remove any foreign bodies (e.g. nail, screw) which have penetrated into the tyre.►Park the vehicle without obstructing traffic and apply the parking brake.►Follow the safety instructions (hazard warning lamps, warning triangle, high visibility jacket, etc.) according to the legislation in force in the country in which you are driving.►Switch the ignition off.►Uncoil the pipe stowed under the compressor.
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131