Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-frontend" was enqueued with dependencies that are not registered: jquery-ui-position. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131

Owner Manuals

Peugeot 2008 2019-2025 Owner's Manual Driving Visiopark 1 - Visiopark 2

138DrivingThe system cannot be deactivated. With Touch screen 10" & Bluetooth Radio & TelephoneYou can start the system manually and activate/deactivate the audible signal in the Driving touch screen menu.With PEUGEOT i-Connect Advanced- PEUGEOT i-ConnectYou can start the system manually and activate/deactivate the audible signal in the ADAS touch screen application.The rear parking sensors are deactivated automatically if a trailer or bicycle carrier is connected to a towing device installed in accordance with the Manufacturer's recommendations.In this case, the outline of a trailer is displayed at the rear of the image of the vehicle.When starting the vehicle, the graphic and audible aids are only available after the touch screen has started up.Operating limitsIf the boot is heavily loaded, the vehicle may tilt, affecting distance measurements.In case of a gearbox failure, the system is not active, when the reverse gear is engaged.MalfunctionIn case of display or speakers malfunction, the system may be disturbed or unavailable.In the event of vehicle malfunction, the system may be deactivated.In the event of a malfunction, this warning lamp lights up on the instrument panel, accompanied by the display of a message and an audible signal (short beep).Have it checked by a PEUGEOT dealer or a qualified workshop.This warning lamp lights up on the instrument panel with the message "Parking Assistance Sensor blind: Clean sensor, see User Manual" if the sensor is masked.This is a normal behavior, which does not request the support of a qualified workshop.In this case, stop the vehicle and verify if the front and/or rear sensors are covered by dirt, mud, sand, snow, ice or anything preventing the sensing.The system is operational again after the detection field has been cleaned.Visiopark 1 - Visiopark 2With PEUGEOT i-Connect Advanced- PEUGEOT i-ConnectVisiopark 1For more information, refer to the General recommendations on the use of driving and manoeuvring aids.When reverse gear is engaged, with the engine running, this system displays views of the vehicle's close surroundings on the touch screen using a camera located at the rear of the vehicle.
139Driving6The screen is divided into 3 parts with a side menu, a contextual view and a view from above the vehicle in its close surroundings.The parking sensors supplement the information in the view from above the vehicle.Different contextual views are available:–Automatic zoom view.–Standard view.–Panoramic view.Depending on the context, the system chooses the best view to display (standard or automatic zoom).The view type can be changed at any time during the manoeuvre.The system status is not saved when the ignition is switched off.Operating principleUsing the camera, the vehicle's close surroundings are recorded during low speed manoeuvres.An image from above the vehicle in its close surroundings is created in real time (on the side of the screen), as the vehicle progresses.This view makes it easier to align the vehicle when parking and to perceive nearby obstacles. It is automatically deleted if the vehicle remains stationary for too long.An additional jet is fitted above the number plate to clean the reversing camera (depending on version).►The washing of the reversing camera is triggered by operating the rear screenwash.SettingsIn the side menu:This window allows to carry out the following operations:–adjust the volume of the audible signal.–trig the camera washing (depending on equipment).This button allows to mute/unmute the audible signal.Activation/DeactivationTo activate the camera, engage reverse gear.The system is deactivated:–when changing out of reverse gear.–by pressing the cross in the top left-hand corner of the touch screen.Automatic zoom viewThe rear camera records the vehicle's surroundings during the manoeuvre in order to create a view from above the rear of the vehicle in its close surroundings, allowing the vehicle to be manoeuvred around nearby obstacles.Using the sensors located on the rear bumper, the automatic zoom view is displayed when approaching an obstacle at the red line (less than 30 cm) during the manoeuvre.This view is only available automatically.Obstacles may appear further away than they actually are.It is important to monitor the sides of the vehicle during the manoeuvre, using the mirrors.Parking sensors also provide additional information about the area around the vehicle.
140DrivingStandard viewThe area behind the vehicle is displayed on the screen.The blue lines 1 represent the width of your vehicle, with the mirrors unfolded; their direction changes according to the position of the steering wheel.The red line 2 represents a distance of 30cm from the rear bumper; the two blue lines 3 and 4represent 1m and 2m, respectively.This view is available automatically or by selection in the side menu.Panoramic viewThe panoramic view allows you to leave, in reverse, a parking space by anticipating the arrival of vehicles, pedestrians or cyclists.This view is not recommended for carrying out a complete manoeuvre.This view is only available by selection in the side menu.Visiopark 2For more information, refer to the General recommendations on the use of driving and manoeuvring aids.This system allows you to view your vehicle's close surroundings on the touch screen using cameras, located at the front and rear of the vehicle.The screen is divided into 4 parts with two side menus, a contextual view and a view from above the vehicle in its close surroundings.The parking sensors supplement the information in the view from above the vehicle.Depending on the view angle chosen in the left-hand side menu, the system provides specific visual assistance in particular driving conditions, such as entering a blind intersection or manoeuvring in areas with reduced visibility.Different contextual views are available for the rear or for the front:–Automatic zoom view.–Standard view.–Panoramic view.Depending on the context, the system chooses the best view to display (standard or automatic zoom).The view type can be changed at any time during the manoeuvre.The system status is not saved when the ignition is switched off.Operating principleReconstructed viewThe cameras are activated and a reconstruction of a view from above your vehicle in its close surroundings is displayed on the touch screen.Live viewThe front and rear views automatically appear in the view from above the vehicle.It is also possible to display any live view by selecting the corresponding zone.The front view can be selected in forward gear up to 10 mph (16 km/h).
141Driving6Installing the very cold climate screen can alter the image transmitted by the front camera.SettingsIn the side menu:This window allows to carry out the following operations:–adjust the volume of the audible signal.–adjust the brightness.–adjust the contrast.–trig the camera washing (depending on equipment).This button allows to mute/unmute the audible signal.Activation/DeactivationAutomaticWith the rear camera, engine running and vehicle stationary, rear vision is displayed automatically if reverse gear is engaged.With the front camera, engine running and speed below 10 mph (16 km/h), rear vision is displayed automatically if a gear is engaged.Manual►In the ADAS touch screen application, select Functions>Panoramic CameraThe system is deactivated:–automatically for the rear, when changing out of reverse gear.–automatically for the front, above approximately 10 mph (16 km/h).–by pressing the cross in the top left-hand corner of the touch screen.Automatic zoom viewThe front or rear camera records the surroundings during the manoeuvre to create a front or rear view from above the vehicle in its close surroundings, making it possible to manoeuvre the vehicle around the surrounding obstacles.Using the sensors located on the front or rear bumper, the automatic zoom view is displayed when approaching an obstacle at the red line (less than 30 cm) during the manoeuvre.This view is only available automatically.Depending on version, it can be activated/deactivated in the ADAS application of the touch screen.Obstacles may appear further away than they actually are.It is important to monitor the sides of the vehicle during the manoeuvre, using the mirrors.Parking sensors also provide additional information about the area around the vehicle.Standard viewDepending on the context, the area behind or in front of your vehicle is displayed on the screen.The blue lines (at the rear)/orange lines (at the front)1 represent the width of your vehicle, with the mirrors unfolded; their direction changes according to the position of the steering wheel.The red line 2 represents a distance of 30 cm from the rear or front bumper; the two blue lines (at the rear)/orange lines (at the front)3 and 4represent 1 m and 2m respectively.This view is available automatically or by selection in the left-hand side menu.Panoramic view
142DrivingThe rear or front panoramic view allows you to leave a parking space by anticipating the arrival of vehicles, pedestrians or cyclists.This view is not recommended for carrying out a complete manoeuvre.This view is only available by selection in the left-hand side menu.
Peugeot & TotalEnergies,a partnership in performance !For more than 25 years of partnership, TotalEnergies and Peugeot have pushed the limits of performance in sports competition with historic victories, in endurance races or in rallies. Today, the two brands continue their common motorsport adventure by setting out to conquer the 24h of Le Mans and the FIA World Endurance Championship in the Hybrid Hypercar category. So many challenges for which Peugeot exclusively recommends high-tech Quartz lubricants for the protection of its engines throughout their life. TotalEnergies therefore equips Peugeot vehicles with Quartz lubricants from their fi rst fi lling in the factory to the approved maintenance networks to guarantee them optimal day-to-day operation. Peugeot & TotalEnergies: offi cial partners in performance !Keep your engine younger for longer !Quartz Ineo Xtra First 0W-20 is a very high performance lubricant resulting from the joint work of the Peugeot and TotalEnergies R&D teams. Its innovative technology extends your engine’s life while reaching signifi cant fuel savings and thus limiting CO2 emissions. The product is now available in new packaging* made of 50% recycled material and 100% recyclable.* 1L & 5L produced in Europe
Scroll to Top

Notice: Function WP_Scripts::add was called incorrectly. The script with the handle "elementor-pro-frontend" was enqueued with dependencies that are not registered: elementor-pro-webpack-runtime. Please see Debugging in WordPress for more information. (This message was added in version 6.9.1.) in /home/u918277800/domains/ownersmanual.store/public_html/wp-includes/functions.php on line 6131